background image

19

18

20

17

21

26

23

18

22

24

25

12”

3” Minimum

Nozzle

Water Level

Air Regulator

Housing

Discharge

Tile

Deck

12”

Concrete

Wall

Air Regulator

Air Line

3”

Minimum

Water Level

Suction

Plaster

Fitting 4”

Pipe

Fitting 4”

45

o

 Elbow

14

Concrete or Gunite Installation - continued

5. Keep all parts not being used now in original box. Store in a safe place until needed.

NOTE: An extension ring and longer square cover screws (part #9/5) are available (upon request) for applications where the 
housing is recessed into the pool wall.

6. Once the concrete or gunite is fully cured and pool wall is completed, install the square cover (part #8) using the four (4) 
M6 x 25mm square cover screws (part #9/1).

NOTE: In tile installations, the tile thickness can be compensated for by first installing the clamping ring gasket (part #12) 
and clamping ring (part #3) before installing the square cover. The clamping ring and clamping ring gasket are installed using 
the eight (8) clamping ring screws (part #9/2, 9/3, or 9/4).

The air regulator can be located in the tile above the 
water level or in the deck. When tiling the pool, adjust 
the air regulator location so it is 3”-4” ABOVE the water 
level. Place and set with hydraulic cement. The air 
regulator holder (part #17) should finish flush with the 
inner pool wall. Drill a 1/2” hole in the tile line even with 
the center hole of the air regulator holder. Tile over the 
air regulator holder. CAUTION: DO NOT plug the center 
hole of the air regulator holder.

Insert the M10 x 80 mm brass screw (part #24) through 
the bottom part of the air regulator (part #23), the 42 
x 11 x 2 mm and the air regulator gasket (part #26). 
Thread the M10 x 80 mm brass screw into the center of 
the air regulator holder (part #17). Tighten with a flat 
head screw driver.

B.

C.

D.

Figure 12
Air Regulator Assembly

Install the hose ring (part #25) and snap the top part of the air regulator (part #22) into place. See Figure 12 for air 
regulator assembly. 

Figure 13

Figure 14

Installation in Concrete or Gunite Pools

BaduStream in Concrete or Gunite Pool.

Summary of Contents for Badu Stream II





























Reviews: