22
EN
FR
DE
ES
CNS
FREE
FREE
PT
REMOVING THE REAR WHEEL ON SINGLE-SPEED MODELS
The steps are the same as the multi-speed Jett models except there is no derailleur.
Disconnect the rear brake cable by squeezing the brake arms together and unhooking the
cable noodle end from the quick release cradle (as seen in
Fig. 3.29
).
Using the provided flat wrench, loosen the rear wheel axle nuts and slide the rear wheel
forward in the dropouts so the chain is loose.
Lift the chain off of the rear sprocket and guide the wheel down and out of the dropouts.
REINSTALLING THE REAR WHEEL ON SINGLE-SPEED MODELS
With the brake cable disconnected, guide the wheel into the dropouts and between the
brake pads.
Seat the rear axle in the dropouts and place the chain on the rear sprocket.
Pull the wheel back until the chain is taut and the rear wheel is centered.
Using the flat wrench, tighten the axle nuts approximately 3/8 of a turn after tension is felt
(21 Nm /186 in-lbf).
Reconnect the rear brake cable by squeezing the brake arms together and inserting the
cable noodle end into the quick release cradle (as seen in
Fig. 3.33
).
Lift the rear end of the bicycle and spin the rear wheel to check if the wheel is centered and
does not wobble.
WARNING! Make sure the spacers are on the outside of the dropouts when
you reinstall the wheel.
P U M P I N G T H E T I R E S
The tires must be inflated and periodically checked and re-inflated using a pump with an
accurate pressure gauge. The tire pressure range is
35-65 PSI / 2.5-4.5 BAR
. Please
refer to the Tires and Tubes section of the Specialized Bicycle Owner’s Manual for additional
information.
WARNING! Never inflate a tire beyond the maximum pressure marked on the tire’s
sidewall. Exceeding the recommended maximum pressure may blow the tire off the
rim, which could cause damage to the bicycle and injury to the rider and bystanders.
4. SAFETY CHECK
WARNING! Before the first ride and routinely thereafter before each ride,
perform the below safety check as well as any additional safety checks
outlined in the Owner's Manual, to ensure the bicycle is safe to ride. Failure to
follow this warning can result in serious personal injury.
1. Nuts, bolts, screws, and other fasteners:
Ensure the seatpost, stem, and handlebar
are properly tightened. You can check the tightness of the handlebar, stem, and seatpost
by securing the bicycle between your legs and trying to twist, push, and pull the handlebar
and saddle. The handlebar and saddle should not move. If any of the components move,
realign the part, increase the bolt tension, and try again. Repeat as necessary until there is
no movement. Periodically check all the bolts on the bicycle to make sure they are torqued to
specification by using the provided torque wrench.
2. Seatpost:
Ensure the saddle height is appropriate. Adjust as necessary.
3. Tires and wheels:
Ensure the wheels spin freely and do not wobble. The wheels should
be centered in the frame and fork. If the wheels wobble and are not centered, please see your
Authorized Specialized Retailer.
4. Tire pressure:
The tires must be inflated and periodically checked and re-inflated using a
pump with an accurate gauge. Please refer to the Tires and Tubes section of the Specialized
Bicycle Owner's Manual supplied with your bicycle for additional information.
5. Brakes:
The brakes are preadjusted and aligned out of the box. If the brake pads or arms
are misaligned, please visit your Authorized Specialized Retailer.
Check the brake pads
periodically for wear. Brake pads should be replaced once they wear down to the wear line.
If the brake pads need to be replaced but you do not have experience replacing brake pads,
please see your Authorized Specialized Retailer. Test the brakes by lifting one end of the
bicycle at a time, spinning each wheel, and squeezing the brake lever (left lever for front
wheel, right lever for rear wheel). If the brakes are not working properly, please see your
Authorized Specialized Retailer.
Regulary inspect the bicycle to ensure there is no damage to any of the components.
Replace any worn or damaged components or have them replaced by your Authorized
Specialized Retailer.
Summary of Contents for 92722-5020
