GB
9
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
SILENCER and properly installed muffler shield.
4.
DO NOT TOUCH or let your hands or body come
in contact with the exhaust. Hold unit with
thumbs and fingers encircling the handles.
5.
D O N O T O P E R A T E U N I T I N A W K W A R D
POSITIONS, off balance, outstretched arms, or
one-handed. Always use two hands when
operating unit with thumbs and fingers encircling
the handles.
6.
DO NOT RAISE CUTTING HEAD above ground
level while unit is operating. Injury to operator
could result.
7.
DO NOT USE UNIT FOR ANY PURPOSES
OTHER than trimming lawn or garden areas.
8.
DO NOT OPERATE UNIT FOR PROLONGED
PERIODS. Rest periodically.
9.
DO NOT OPERATE UNIT WHILE UNDER THE
INFLUENCE OF ALCOHOL OR DRUGS.
10. DO NOT OPERATE UNIT UNLESS DEBRIS
SHIELD AND/OR GUARD IS INSTALLED AND
IN GOOD CONDITION.
11. DO NOT ADD, REMOVE OR ALTER ANY
COMPONENTS OF THIS PRODUCT. Doing so
could cause personal injury and/or damage the
unit voiding the manufacturer’s warranty.
12. DO NOT operate your unit near or around
flammable liquids or gases whether in or out of
doors. An explosion and/or fire may result.
13. DO NOT USE ANY OTHER CUTTING TOOLS.
For your own safety only use the accessories
and additional equipment specified in the
operating manual or recommended or specified
by the manufacturer. The use of tools or
accessories other than those recommended in
the operating manual or catalog may place you in
danger of personal injury.
2. Layout and items supplied (Fig. A, B
and C)
A/1, B/1 Cutting head
A/2 Cutting
line
A/3, B/3 Outer guard hood
A/4, B/4 Cutting blade
A/5, B/5 Inner guard hood
A/6, B/6 Long handle with drive shaft
A/7, B/7 "Bike” handle
A/8
Throttle lever in the right-hand handle
A/9
Engine switch "off” and "on”
A/10
Throttle lever "lock”
A/11
Throttle lever "release”
A/12
Levers for "Choke" - "Half Choke" - "Full
Choke"
A/13
Housing for engine cooling and starter
A/14 Petrol
tank
A/15
Air filter cover
A/16
Handle for cable pull start
A/17
Petrol accumulation button
A/18,B/18 Carrying strap
A/19
Retainer screw for long handle with drive
shaft
B 20
Tool for cutting head and cutting wire
C/21
3 M5 screws for inner guard hood
C/22
3 M6 screws for outer guard hood
C/23 Spacer
sleeve
C/24
Carrier plate for cutting head or cutting
blade
C/25
Pressure plate for cutting blade assembly
C/26
Fastening nut for cutting blade
C/27 2xCable
tie
C/28
Safety split pin
C/29
Retainer pin for carrier plate
C/30
Key for spark plug and fastening nut
SAFETY DEVICES
It is imperative that the GUARD HOOD is assembled
in order to prevent injuries to the operator due to
objects thrown out by the machine. In addition, the
integrated blade in the guard hood automatically cuts
the cutting line to the optimum length.
TECHNICAL SPECIFICATIONS
Engine type:
Air cooled 2-stroke engine,
cylinder hard-chromium plated
Displacement 28
cm
3
Power:
0.75 kW / 1 HP
Dry weight
5.8 kg
Fuel capacity
520 ccm
Guide bar length
147 cm
Cutting width with twin line
43 cm
Line diameter
2.5 mm
Cutting width with cutting blade
23 cm
Cutting blade
4 teeth
Handle “Bike”
handle
Ignition Electronic
Spark plug
Champion RDJ 8J
Drive Centrifugal
clutch
LPA sound pressure level
103 dB(A)
LWA sound power level
113 dB(A)
Vibration 11.41
m/s
2
max. RPM with twin line
8500 min
-1
max. RPM with cutting blade
11,000 min
-1
Idle speed
3050 ± 350 min
-1
Petrol consumption
620 g/kWh
Anleitung SPJBC 28 11.10.2006 17:47 Uhr Seite 9
