4
Operating Instructions
SP-HDS-700 1x4 HDMI Splitter Over Ethernet
Cable
Item no: 2369286
1 Intended use
The product is an HDMI splitter comprising a transmitter and receivers. The transmitter distributes the
HDMI source signal to up to 4 receivers using twisted pair cables. The HDMI splitter supports one-way IR
control and EDID management.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, electric shocks or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to
third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
2 Delivery contents
■
1x HDMI transmitter
■
4x HDMI receivers
■
1x IR blaster cable (1.5 m)
■
4x IR receiver cables (1.5 m)
■
5x Mounting bracket with screws
■
Power adaptor
■
Operating instructions
3 Latest product information
Download the latest product information at
www.conrad.com/downloads
or scan the QR code shown. Fol-
low the instructions on the website.
4 Description of symbols
The symbol with the exclamation mark in the triangle is used to indicate important informa-
tion in this document. Always read this information carefully.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety informa-
tion. If you do not follow the safety instructions and information on proper handling,
we assume no liability for any resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
5.1 General
■
The product is not a toy. Keep it out of the reach of children and pets.
■
Do not leave packaging material lying around carelessly. This may become dangerous playing mater-
ial for children.
■
If you have questions which remain unanswered by this information product, contact our technical
support service or other technical personnel.
5.2 Handling
■
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
■
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
■
Consult an expert when in doubt about the operation, safety or connection of the appliance.
5.3 Operating environment
■
Do not place the product under any mechanical stress.
■
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
■
Protect the product from high humidity and moisture.
■
Protect the product from direct sunlight.
■
Do not switch the product on after it has been taken from a cold to a warm environment. The con-
densation that forms might destroy the product. Allow the product to reach room temperature before
you use it.
5.4 Power adapter
Do not tamper with power supply components. Risk of death by electric shock!
■
Always ensure proper connection.
■
Never use damaged power supply components.
■
Do not modify power supply components.
■
Connect the appliance to a wall socket that can be accessed easily.
■
As power supply, only use the supplied mains adaptor.
■
Only connect the power adaptor to a normal mains socket connected to the public supply. Before
plugging in the power adaptor, check whether the voltage stated on the power adaptor complies with
the voltage of your electricity supplier.
■
Never connect or disconnect power adaptors if your hands are wet.
■
Never unplug the power adaptor from the mains socket by pulling on the cable; always use the grips
on the plug.
■
For safety reasons, disconnect the power adaptor from the mains socket during storms.
■
Do not touch the power adapter if there are any signs of damage, as this may cause a fatal electric
shock! Take the following steps:
– Switch off the mains voltage to the socket containing the power adapter (switch off the correspond-
ing circuit breaker or remove the safety fuse, and then switch off the corresponding RCD protective
switch).
– Unplug the power adapter from the mains socket.
– Use a new power adapter of the same design. Do not use the damaged adapter again.
5.5 Connected devices
■
Also observe the safety and operating instructions of any other devices which are connected to the
product.
6 Product overview
6.1 HDMI Transmitter
IN
1
2
3
4
LOOP
OUT
ON
OFF
IN
AUDIO OUT
HDMI
OUT
DC 12V
CAT OUTPUT
LOOP OUT
1
2
3
4
IR
A1
A2
A3
A4
A5
A6
A7
A8
A9 A10 A11
A12
A13
A15
A14
No
Part
Description/Function
A1
Switch
ON/OFF
Switch the HDMI transmitter on and off.
A2
Power indicator light
Lights up when the HDMI transmitter is powered on.
A3
Indicator
IN
Lights up when an HDMI source is connected.
A4
Indicator
LOOP
Lights up when an HDMI display device is connected to the
HDMI LOOP OUT
port.
A5
Indicator
OUT
Indicates that a HDMI receiver is connected to the corres-
ponding
CAT OUTPUT
receiver port.
A6
Audio out connectors
Coaxial (
COAX
)/Analog (
L/R
) audio output. Connect a
speaker or amplifier.
Importan
t:
The
L/R
jack is a 3.5 mm TRS jack.
Only connect compatible jack plugs.
A7
HDMI ports
HDMI IN
Port for HDMI source. Connect a media box.
HDMI LOOP OUT
Port for HDMI display device. Connect a TV or display.
A8
Receiver ports
CAT OUTPUT
Connect HDMI receivers.
A9
Link signal indicator
Lights up when a HDMI receiver is connected.
A10
Data signal indicator
When a HDMI receiver is connected:
Solid on: Indicates an HDMI signal with HDCP
Blinking: Indicates an HDMI signal without HDCP
A11
Infrared controller port
IR OUT
Connect the IR blaster cable for IR control.
A12
Power supply socket
Connect the power adaptor.
A13
EDID
switches
Set the EDID mode.
A14
Mounting holes
Attach mounting bracket.
A15
Port
SERVICE
Connect a PC to send ASCII commands.
6.2 HDMI Receiver
HDMI OUT
DC 12V
IR IN
SERVICE
CAT IN
B1
B2
B3 B4
B5
B6
B7
