• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Consult a technician if you are not sure how to use or connect the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Electrical safety
• The mains outlet must be located near to the device and be easily accessible.
• As power supply, only use the supplied mains adapter.
• Only connect the power adapter to a normal mains socket connected to the public
supply. Before plugging in the power adapter, check whether the voltage stated on
the power adapter complies with the voltage of your electricity supplier.
• Never connect or disconnect power adapters if your hands are wet.
•
Never unplug the power adapter from the mains socket by pulling on the cable;
always use the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• For safety reasons, disconnect the power adapter from the mains socket during
storms.
• The power adapter is manufactured according to protection class II.
• Do not touch the power adapter if there are any signs of damage, as this may
cause a fatal electric shock! Switch off the mains voltage to the mains socket that
you used to connect the power adapter (switch off at the corresponding circuit
breaker or remove the safety fuse, then switch off at the corresponding RCD
protective switch, so that all poles of the mains socket are disconnected), and
then unplug the power adapter from the mains socket. Dispose of the faulty power
adapter in an environmentally friendly way and discontinue use. Replace it with a
power adapter of the same design.
•
Never pour any liquids over electrical devices or put objects filled with liquid right
next to the device. If liquid or an object does enter the interior of the device, power
down the respective socket (e.g. switch off circuit breaker), and then pull the mains
plug from the mains socket. Discontinue use and take the product to a specialist
repair centre.
• Never use the product immediately after it has been brought from a cold room
into a warm one. The condensation generated could destroy the product, and the
power adapter may cause a fatal electric shock! Allow the product to reach room
temperature before connecting it to the power supply and putting it to use. This
may take several hours.
• Do not cover any of the ventilation grilles, otherwise the splitter may not cool
properly. Ensure that there is sufficient ventilation. Do not cover the device
housing!
c) Batteries
• Correct polarity must be observed while inserting the battery.
• The battery should be removed from the device if it is not used for a long period of
time to avoid damage through leaking. Leaking or damaged batteries may cause
acid burns if they come into contact with skin. Always use protective gloves when
handling damaged batteries.
• The battery must be kept out of the reach of children. Do not leave the battery lying
around, as there is a risk that children or pets may swallow it.
•
Batteries must not be dismantled, short-circuited or thrown into fire. Never
recharge non-rechargeable batteries, as this may cause them to explode.
Operating elements
a) Front
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
ON/OFF
button
2 Standby LED
3 HDMI
Switch
button
4
ARC
(Audio return channel) button
5
Video
(Video EDID) button
6
Audio
(Audio EDID) button
7
OUT1-OUT 4
LEDs (indicates the status
of the HDMI outputs)
8 Infrared sensor
9
IN1-IN2
LEDs (indicates the status of the
HDMI inputs)
10
ARC
LED
11
PASS
LED (Video EDID)
12
4K
LED (Video EDID)
13
3D
LED (Video EDID)
14
ADV
LED EDID (audio)
15
5.1CH
LED EDID (audio)
16
2.0CH
LED EDID (audio)
Operating instructions
2x4 HDMI splitter
Item no. 1497182
Intended use
This HDMI splitter features two HDMI inputs and four HDMI outputs. Use the splitter to send an
HDMI signal from a source device (e.g. a Blu-Ray™ player or computer) to up to four display
devices. You can display the same image on all connected devices in 2D and 3D. The audio
signal can be decoupled via ARC and sent through the optical output (TOSLINK). You can
switch between inputs using the remote control provided. Power is supplied by a separate
power adapter.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g.
in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
Delivery content
• HDMI splitter
• Power adapter (5 V / 2 A)
• Remote control (includes CR2025 button cell)
• 4x rubber feet
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
above. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
This symbol indicates particular hazards during handling or operation.
The “arrow” symbol indicates special tips and operating information.
The product must only be used in dry, enclosed indoor areas. This product must not
become damp or wet, as this may result in a fatal electric shock!
This symbol indicates that this product is built according to protection class II. It is
equipped with reinforced or dual insulation between the mains circuit and the output
voltage.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
