background image

GB

GB

 7

Blower  
connecting lead

Mains supply  
230 V 50 Hz

Temperature sensor with plug Control unit

4.3. FLEXIBLE ALUMINIUM TUBES

The flexible aluminium tube supplied should be divided into the necessary 
number of sections according to on-site conditions.

designing the covering so that the control unit is positioned near an air 
grille. That way, the operating status display can be checked at any time 
and accessibility is ensured. All the necessary components (mains plug, 
connecting lead to the blower, temperature sensor) are connected to this 
control unit.

4.5. TEMPERATURE SENSOR

The temperature sensor supplied should be integrated into the convection 
air housing in a suitable position. It should be borne in mind that the blower 
will be automatically switched on by the controller when the temperature 
reaches approx. 105°C, irrespective of the mode set. This is to prevent 
overheating of the convection air housing.

The sensor length is approx. 2 metres. We recommend installing it from above 
in the convection air housing cover, near the connecting piece in order to 
ensure the accessibility of the screw fittings for installation purposes.

The connecting lead to the temperature sensor must be routed outside the 
convection air housing. The lead can be lengthened to a maximum of 4 
metres if necessary. The polarity of the lead is not relevant.

The pipe connections should be connected together with flexible aluminium 
tubes to form two separate trains. Starting from the blower unit, connect up 
two pipe connections using a separate flexible aluminium tube in each case. 

4.4. CONTROL UNIT

All the electronics are housed in the control unit housing. The control unit 
should be integrated into the fireplace covering such that accessibility 
is ensured. The maximum ambient temperature is 60°C. We recommend 

Quick-acting 
fine-wire F 2A

Acoustic signal transmitter

Temperature 
sensor 
connection

Blower 
connection

Mains plug 
connection 

Operating 
status display

Convection air

Pipe connection with 
cover plate 

flexible aluminium

Pipe connection with 

cover plate

Summary of Contents for S-Vent 100

















Reviews: