background image

GB

GB

 13

•  the glass ceramics: Soiling caused by soot or burnt-in residues of burnt 

materials as well as visibly changed colour or other aspects due to ther-
mal stress.

• Improper transport and/or incorrect storage
• Improper handling of fragile components such as glass and ceramics
• Improper handling and/or use
• Lack of maintenance
• Incorrect installation or connection of the unit
• Non-observance of the installation and operating instructions
• Technical modifications to the unit by third parties

9.6. DEFECT REMEDIATION/REPAIRS

Notwithstanding the statutory guarantee, which shall take precedence over 
our warranty during the statutory guarantee periods, within the scope of our 
warranty we will remedy free of charge all defects demonstrably due to a 
material fault or manufacturing error, provided that the other terms and con-
ditions of this warranty undertaking are observed. In accordance with this 
warranty undertaking Spartherm Feuerungstechnik GmbH reserves the right 
either to rectify the defect or to replace the unit free of charge. Remediation 
of defects shall take precedence. This warranty undertaking expressly does 
not cover further compensation exceeding the statutory guarantee.

9.7. EXTENSION OF WARRANTY

In the case of performance in accordance with the terms of the warranty, 
whether remediation of defects or replacement of a unit, the warranty period 
shall be extended in respect of the replacement unit/components. 

9.8. SPARE PARTS

No spare parts other than those produced or recommended by the manu-
facturer shall be used.

9.9. LIABILITY

Damage and compensation claims not based on a defective unit supplied 
by Spartherm Feuerungstechnik GmbH are excluded and are not covered by 
the warranty undertaking. This does not apply to statutory warranty claims 
arising in a particular case.

9.10. NOTE

Your specialist dealer/contractor will gladly advise and assist you in matters 
not covered by our warranty terms and conditions and undertakings. We 
particularly advise you to have your fireplace insert/stove serviced regularly 
by a stove fitter.

Technical data subject to change errors and omissions excepted.

Summary of Contents for S-Vent 100

















Reviews: