background image

Page 24

One Year Parts Warranty:

For one year from the date of original purchase, your local reseller will provide free of charge, non-consumable replace

-

ment parts or components that failed due to manufacturing defects. Subject to the conditions and limitations set forth 

below, your local reseller will, at its option, either repair or replace any part of its products that prove defective by reason 

of improper workmanship or materials. Repaired parts or replacement products will be provided by your local reseller 

on an exchange basis, and will be either new or refurbished to be functionally equivalent to new. The consumer is re

-

sponsible for all shipping costs. Consumable parts not covered by this warranty include but not limited to: Light bulbs, 

metal, aluminum and charcoal filters.

Who is Covered:

This warranty is extended to the original purchaser for products purchased for ordinary home use.

This Warranty Will Be Voided When:

Product damaged through negligence, improper installation, accident, abuse, misuse, natural disaster, insufficient or 

excessive electrical supply, abnormal mechanical or environmental conditions, or any unauthorized disassembly, repair, 

modification, or failure to follow installation instructions. When product is used commercially or other than its intended 

purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by 

anyone other than your local reseller’s authorized agents. This limited warranty also does not apply to any product on 

which the original identification information has been altered, obliterated or removed, has not been handled or packaged 

correctly or has been sold as second-hand.

What is Not Covered:

Consumable parts such as light bulbs, metal and charcoal filters. The natural wear of finish, and wear due to improper 

maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner products. Chips, dents or cracks 

due to abuse, misuse, freight damage, or improper installation. Damage of product caused by accident, fire, floods or 

act of God. The manufacturer and/or distributor/reseller is not liable for, and does not cover under warranty, any loss of 

properties or any costs associated with removing, servicing, installing, or determining the source of problems with this 

product.

This warranty is valid in the country of the original purchase at retail. It is non-transferable and applies only to the original 

purchaser and does not extend to subsequent owners of this product. Any applicable implied warranties, including the war

-

ranty of merchantability, are limited in duration to a period of express warranty as provided herein beginning with the date 

of original purchase at retail and, no warranties, whether express or implied, shall apply to this product thereafter. 
To obtain warranty service, you may contact your local reseller from which you purchased this product. Please confirm the 

terms of your local reseller’s policies prior to contacting. Typically, you must include product identification information, 

including model number and serial number with a detailed description of the problem you are experiencing. You must also 

include proof of the date of original retail purchase as evidence that the product is within the applicable warranty period.

The  information  in  this  document  is  subject  to  change  without  notice,  please  contact  your  local  reseller  for  updated  details.

Warranty

Summary of Contents for PS29





























Reviews: