background image

 

Form 43343530 

-56- 

Aug 2012 

 

26.0)

 

WARNINGS CARD 

Copies of this card may be ordered at no charge under part no. 43344990 for installation near the heater. 
 
 

  

 

IF YOU SMELL GAS:

FOR YOUR SAFETY

DO NOT

 try to light any appliance.

DO NOT

 touch any electrical switch; 

DO NOT

 use any telephone in your building.

IMMEDIATELY

 call your gas supplier from a neighbor's telephone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

Attach this information card adjacent to the thermostat which controls the Space-Ray heater(s).

Read the Installation and Operating Instructions thoroughly before installation, operation or
service.

INSTALLER: Write the clearance distance for the highest BTU model in the building in the blank spaces
below using permanent ink. The clearances to combustible materials are based on each individual
heater model number. Locate the heater model number on the nameplate affixed to the heater. The
clearances to combustibles distances can be located adjacent to the nameplate or in the Installation
& Operating (I & O) Instructions.I & O’s can also be located on www.spaceray.com

Maintain the following clearances:

_____ to the side, _____ above

and _____below the heater

from combustible materials.

43344990
July 2012

Installation Code and Annual Inspections:

Installation and Service of Space-Ray equipment must be performed by a qualified contractor and conform with all requirements
set forth in the Space-Ray Installation and Operating Instructions and any National and Local codes pertaining to the
installation, service and operation of the equipment. Annual inspection is recommended prior to the heating season to ensure
proper operation of the heating equipment.

Maintain Clearances to Combustibles to
Prevent the Risk of Fire.

Clearance to combustibles must be
maintained at all times in order to prevent
the ignition of combustible materials. In
locations used for the storage of combustible
materials signs must be posted to specify
the maximum permissible stacking height
to maintain the required clearances from
the heater to the combustibles. Signs must
either be posted adjacent to the heater’s
thermostats or in the absence of such
thermostats, in a conspicuous location.

SPACE-RAY

Post Office Box 36485 (28236)  *  305 Dogget Street (28203)  *  Charlotte, North Carolina
Phone (704) 372-6391  * Fax (704) 332-5843 *  www.spaceray.com  *  email: [email protected]

FIRE HAZARD

Combustible material must be located
outside the clearance distance listed
from heater.

Some objects will catch fire or
explode when placed close to heater.

Failure to follow these instructions
can result in death, injury or property
damage.

WARNING

 

Summary of Contents for PTS Series 200


























































Reviews: