background image

Form 43343530 
Aug 2012

 

-17- 

9.0)

 

TYPICAL SUSPENSION METHODS 

Burner must be secured to the mounting flange with nuts.

All materials used to suspend the heater must have a minimum working load
of 115 lbs.
All “S” Hooks must be crimped closed.

Never use the heater to support a ladder or other access equipment.
Failure to do so may result in death, serious injury or property damage.

SUSPENSION HAZARD

 

Various means of suspending the heater can be used.  See the following drawings for typical examples. 

1.

 

Use only noncombustible materials for suspending hangers and brackets. 

2.

 

A minimum No. 2 chain with a working load limit of 115 lbs. is required. 

3.

 

Turnbuckles can be  used  with chains  to  allow  leveling  of  the heater.   All  “S” hooks and eye bolts  must be 
manually crimped closed by the installer. 

4.

 

When using rigid means for heater suspension (rod, flat bar, etc.) provide sufficient lengths or swing joints to 
compensate for expansion.  See Figures b and c. 

5.

 

Heaters subject to vibration must be provided with vibration isolating hangers. 

6.

 

Heaters must not be  supported  by  gas  or  electric  supply  lines and must be  suspended  from  a  permanent 
structure with adequate load capacity. 

Space-Ray  recommends  that  the  body  sections  be  suspended  using  chains  with  turnbuckles.    This  will  allow 
slight adjustments after assembly and heater expansion/ contraction during operation. 

If a “trapeze” method is used for tube support/hanger brackets (shown below), the minimum chain length for the 
two  connecting  chains  is  36”  to  minimize  any  vibration  that  might  be  generated  by  the  burner  box.    If  these 
chains must be less than 36”, then do not use the trapeze method and, instead, use individual chains on each 
tube support/hanger bracket.   

Eyebolt

Turnbuckle

Minimum
No. 2 Chain

Eyebolt

c.

Threaded
Rod

Turnbuckle

Eyebolt

b.

3/16” x 1”
wideFlat Bar

Minimum
No. 2 Chain

a.

S-Hook crimped
closed (typical)

Wire Hanger

Wire
Hanger

36” (91cm) Minimum

Tube Support/
Hanger Bracket

d.

Failure to install the burner box suspension
chain vertically will void the manufacturers
warranty.

Burner Box Suspension

Eye bolt

Turnbuckle

 

 

Summary of Contents for PTS Series 200


























































Reviews: