SOYO SY-V6BE+ User Manual Download Page 45

Page: 45 / 70

BIOS Setup Utility

SY-V6BE+

3-3.1 Virus Warning

Setting

Description

Note

Disabled

Default

Virus Warning

Enabled

Enable this option to protect
the boot sectors and
partition tables of your hard
disk. Any attempt to write to
them will the system to halt
and display a warning
message.

3-3.2 Cache Memory Options

Setting

Description

Note

Disabled

CPU Internal Cache

Enabled Enables the CPU's

internal cache.

Default

Disabled

External Cache

Enabled Enables the external

memory.

Default

3-3.3 System Boot Control Settings
System Boot
Control Settings

Setting

Description

Note

Disabled

Default

Swap Floppy
Drive

Enabled

Changes the sequence of A
and B drives.

Puts numeric keypad in
NumLock mode at boot-up.

Default

Boot Up
NumLock
Status

Off

Puts numeric keypad in
arrow key mode at boot-up.

Summary of Contents for SY-V6BE+







































































Search results

Summary of Contents for SY-V6BE+

Reviews:

Related manuals for SY-V6BE+

Brands by name

Popular brands

SOYO SY-V6BE+, User Manual

Search results

Summary of Contents for SY-V6BE+

Reviews:

Related manuals for SY-V6BE+

Brands by name

Popular brands