SOYO SY-V6BE+ User Manual Download Page 40

Page: 40 / 70

BIOS Setup Utility

SY-V6BE+

3-1.5 CPU Device Monitoring
CPU Device
Monitoring

Setting

Description

Note

Disabled

AGP – 2X Mode

Enabled

Enable only if your AGP
card supports 2x mode
(faster)

Default

Disabled

Default

CPU Warning
Temperature

Enabled

Set CPU temperature from
50

C to 70

C. The CPU will

slow down when CPU
temperature goes beyond
the preset value. The CPU
will continue to run slow
until the temperature
returns back within the safe
range.

Current System
Temp.

Show the current status of
the system temperature.

Current CPU1
Temperature

Show the current status of
CPU temperature.

Current
CPUFAN1 Speed

Show the current status of
CPU Fan

Current
CPUFAN2 Speed

Show the current status of
the chassis Fan

VID, VTT, 3.3V,
+12V, -5V, +5V,
-12V

Show the current voltage
status.

Summary of Contents for SY-V6BE+







































































Search results

Summary of Contents for SY-V6BE+

Reviews:

Related manuals for SY-V6BE+

Brands by name

Popular brands

SOYO SY-V6BE+, User Manual

Search results

Summary of Contents for SY-V6BE+

Reviews:

Related manuals for SY-V6BE+

Brands by name

Popular brands