Soyal AR-727CM Operation Manual Download Page 10 | Manualshive

Page: 10 / 12

background image

Step 10: AR-727CM already gets IP address now shown as follows:

Note that save it after set all parameters.

Step 11: If AR-727CM connects to soyal controller, please switch DIP Switch position

to OFF, OFF, ON, OFF to RS-485 RUN Mode.

9

«
...
8
9
10
11
12
»

Summary of Contents for AR-727CM













Reviews:

No comments

Related manuals for AR-727CM

Brand: Danfoss Pages: 7

Brand: Danfoss Pages: 16

VLT 2800 Series

Brand: Danfoss Pages: 34

VLT AutomationDrive FC 300

Brand: Danfoss Pages: 60

VLT 5000 Series

Brand: Danfoss Pages: 63

Brand: Teac Pages: 18

CSI-25KTL-GS-FLB

Brand: Canadian Solar Pages: 53

Brand: Cosel Pages: 62

Brand: N-Tron Pages: 2

Brand: Briggs & Stratton Pages: 60

Brand: Helvest Pages: 2

Brand: Kramer Pages: 12

Brand: Baja Silueta Pages: 99

Brand: Delta Electronics Pages: 2

CONSONANCE REFERENCE DB1

Brand: Opera Pages: 3

INTERNATIONAL TRAVEL ADAPTER

Brand: Igo Pages: 1

Brand: Lampizator Pages: 32

Brand: Wacker Neuson Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands