Questions? Call Toll Free at 1-800-737-2112
Copyright © 2008 MAT Engine Technologies, LLC
Questions? Call Toll Free at 1-800-737-2112
Copyright © 2008 MAT Engine Technologies, LLC
Edger Specifications
• Save all instructions
Parts & Features
Unit Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 lb. (32kg)
Cutting Depths . . . . . . . . . . . . . . . . . . . 0-3.0 in. (0-76 mm)
Blade Diameter. . . . . . . . . . . . . . . . 9 in. (228 mm), 3 point
Gasoline Type . . . . . Regular Unleaded / 88 Octane (min.)
Gasoline Capacity . . . . . . . . . . . . . . . . . . . . . 3.5 qt. (3.3L)
Oil Type (API SG-SL) 10W-30 is recommended for all ser-
vice temperatures. See page 7 for additional information.
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . 19 oz (562 ml)
Spark Plug Model. . . . . . . . . . . . . . . . . . . . . . Torch F7RTC
1. Start Lever
Lever on handle which allows the engine to
run. When lever is released, engine will stop.
2. Primer Bulb
Injects fuel mixture into the carburetor for
cold starting the engine.
3. Muffler
Location of engine exhaust.
4. Adjustable Rear Wheel
Right rear wheel is adjustable to
level the edger when edging along a curb (curb-hopping).
5. Adjustable Front Wheels
Front wheels are adjustable from
side to side for balance. The front wheels can also adjust
down for curb-hopping.
6. Recoil Starter Handle
The engine is equipped with an
easy pull recoil starter.
7. Index Lever
Permits adjusting the cutting angle to 15
degrees, 0 degrees (vertical), or -15 degrees. To change
the angle, pull the index lever and rotate the quill assembly
to the desired angle.
8. Blade
Rotating cutting element.
9. Blade Guard
Prevents stones and debris from being
thrown at the operator.
10. Spark Plug/Spark Plug Wire
Provides spark to ignite air/
fuel mixture. The Spark Plug Wire must be disconnected and
moved away from the Spark Plug when servicing the unit.
11. Air Filter
Removes debris and contaminates from in-
take air, allowing engine to run smoothly with low exhaust.
12. Depth Selector Plate, 13. Depth Control Lever,
14. Control Rod
Used to control the edging depth of cut.
15. Flameout Wire Terminals
Must be connected for the
Start Lever to function.
Spark Plug Gap . . . . . . . . . . . 0.028-0.031 in. (0.7-0.8 mm)
Engine Type . . . . . . . . . . . . .
4 Stroke, single cylinder, OHV
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163cc
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000 RPM
Torque Rating. . . . . . 6.5 ft-lbs gross torque per SAE J1940
Bore Diam. x Stroke. . . . . . . . . . . . 2.7X1.8 in. (68X45 mm)
Intake Valve Clearance . 0.0032-0.0047 in.(0.08-0.12 mm)
Exhaust Valve Clearance . 0.0059-0.0079 in.(0.15-0.20mm)
Angle of Ignition . . . . . . . . . . . . . . . . . . . . . . . . 25 Degrees
Read and follow the assembly instructions. Do not discard any parts or materials until the unit is assembled.
References to the right or left side of the edger are from the viewpoint of the operator’s position behind the edger.
Do not operate edger if it is damaged or not completely and correctly assembled.
Before doing any assembly or maintenance to the unit, remove the wire from the spark plug.
Always wear ANSI compliant safety glasses with side shields while assembling the edger.
Assembly
• Save all instructions
1. Assemble the upper handle to the lower handle with the
(2) pipe bolts and the (2) plastic wing nuts. Firmly hand-
tighten the wing nuts.
2. Slide one end of the control rod into the hole of the
Depth Control Lever. Secure with hairpin.
3. Slide the other end of the control rod through the hole of
the quill arm. Secure with second hairpin.
4. Attach the recoil starter handle through the rope guide,
by twisting it into position.
5. Remove the temporary insert from the engine flameout
wire terminal.
6. Connect the flameout wires from the engine and handle.
Use cable tie to secure loose wire to handle.
The following components will be found in the carton.
Quantities shown in ( ).
1. (1) Edger
2. (1) Edger Operator’s Manual
3. (1) Upper Handle
4. (1) Control Rod
5. (1) Bottle of SAE 30 Engine Oil
6. (1) Parts bag containing the following:
(2) Hair Pins
(2) Plastic Wing Nuts (M8)
(2) M8x35mm Pipe Bolts
(1) Wire Tie
(1) Spark plug socket wrench w/ rod
1. Remove all parts and packaging components.
2. Use a utility knife to cut all 4 vertical edges and lay the
side panels flat around the edger.
3. Remove any remaining packaging.
4. Roll the unit out from the carton, and place on a hard
level surface.
How to Remove Edger from Carton
A
How to Assemble the Handle
B
Flameout wires MUST be connected for correct engine
operation. Failure to connect can result in serious injury.
If you need assistance or find any parts missing, CALL
TOLL FREE: 1-800-737-2112.
NOTE:
Refer to Figure 2 when following steps below:
5
6
WARNING
WARNING
WARNING
DANGER
WARNING
Figure 1
FRONT VIEW
Upper
Handle
Lower
Handle
Hair Pin
Control Rod
Quill Support
Arm
Hair Pin
Pipe
Bolt
Figure 2
Depth Control
Lever
Recoil
Starter
Handle
Plastic
Wing Nut
Handle
Flameout
Wire
Engine
Flameout
Wire
Connection
Terminal
Rear View
7
3
10
1
6
2
4
5
9
8
13
12
14
11
15