background image

Questions? Call Toll Free at 1-800-737-2112

 

 

Copyright © 2008 MAT Engine Technologies, LLC

Questions? Call Toll Free at 1-800-737-2112

 

 

Copyright © 2008 MAT Engine Technologies, LLC

PROBLEM

POSSIBLE CAUSE(S)

SOLUTION(S)

Engine difficult to start

1. Out of fuel

2. Start lever is not compressed

3. Engine is not primed.

4. Spark plug wire disconnected

5. Fouled spark plug

6. Dirty Carburetor

7. Clogged air filter

8. Clogged fuel filter

9. Contaminated Fuel

1. Add fresh fuel

2. Pull start lever against handle

3. Push primer bulb 3 times - waiting 2 

seconds between each push.

4. Attach spark plug wire to spark plug

5. Remove spark plug.  Inspect.  Replace if 

necessary

6. Take unit to an authorized service center 

for Carburetor cleaning

7. Remove and clean air filter

8. Remove fuel filter.  Inspect.  Replace if 

necessary

9. Drain fuel tank.  Clean fuel tank. Fill with 

fresh fuel

Engine Problems

Engine smokes excessively

Engine runs very “rough”

Engine runs erratically

Engine cannot maintain full speed

1. No Engine Oil

2. Engine oil not at proper level

3. Fouled spark plug

4. Clogged air filter

5. Clogged fuel filter

6. Contaminated Fuel

7. Carburetor out of adjustment

1. Add engine oil

2. Check engine oil.  Add or drain engine oil if 

necessary

3. Remove spark plug.  Inspect.  Replace if 

necessary

4. Remove and clean air filter

5. Remove fuel filter.  Inspect.  Replace if 

necessary

6. Drain fuel tank.  Clean fuel tank. Fill with 

fresh fuel

7. Take unit to an authorized service center 

for Carburetor adjustment

Excessive vibration / noise

1. Loose parts

2. Engine problems (above)

1. Tighten all fasteners

2. Refer to engine solutions (above)

Blade will not rotate

1. Debris interfering with blade

2. Blade loose

3. Belt Loose

1. Remove debris from around blade

2. Tighten blade nuts

3. Replace Belt

Engine will not stop

Flameout wire terminals 

disconnected

Connect handle and engine flameout wire 

terminals

Blade will not cut properly

Damaged or worn blade

Replace blade

Frequent engine stalling

1. Excessive edging speed / depth

2. Engine problems (above)

1. Edge at a moderate pace.  Make multiple 

passes.

2. Refer to engine solutions (above)

Warranty

• Save all instructions 

Always specify model number when contacting the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written 

warranty. We make no other warranty, expressed or implied. MAT Engine Technologies, LLC warrants this Lawn Edger and any parts 

thereof, to be free from defects in material and workmanship for two years (90 days for commercial use or for reconditioned unit) 

from the date of first purchase from an authorized dealer, provided that the product has been properly maintained and operated in 

accordance with all applicable instructions. This warranty is extended only to the original retail purchaser. The bill of sales or proof of 

purchase must be presented at the time a claim is made under this warranty. This warranty does not cover commercial, industrial, or 

rental usage, nor does it apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become 

damaged as a result of misuse, accident, lack of proper maintenance, tampering, or alteration. Travel, handling, transportation, and in-

cidental costs associated with warranty repairs are not reimbursable under this warranty and are the responsibility of the owner. To the 

full extent allowed by the law of the jurisdiction that governs the sale of the product, this express warranty excludes any and all other 

expressed warranties and limits the duration of any and all implied warranties, including warranties of merchantability and fitness for 

a particular purpose to two years from the date of first purchase, and MAT Engine Technologies, LLC’s liability is hereby limited to the 

purchase price of the product and MAT Engine Technologies, LLC shall not be liable for any other damages whatsoever including indi-

rect, incidental, or consequential damages. Some states do not allow limitation of how long an implied warranty lasts or an exclusion or 

limitation of incidental or consequential damages, so the above limitation of damages may not apply to you. This warranty provides the 

original purchaser with specific rights.
For information regarding those rights, please consult the applicable state laws.

METL Corporate Office - CORRESPONDENCE ONLY

ATTN: Technical Service – METL

625 Barclay Blvd.

Lincolnshire, IL  60069

Southland™ LAWN EDGER Limited Warranty

A

 

18

 

 

17

 

Maintenance 

(Continued)

• Save all instructions 

Summary of Contents for Edger King S-WLE-1639
























Reviews: