background image

 

 

Page 1 of 17 

Summary & Introduction 

 

Summary & Introduction 

 

Summary 

 

These instructions do not intend to cover all details or variations in equipment, or provide for every 

possible contingency to be met in connection with installation, operation or maintenance.  Should 

information be desired or should particular problems arise which are not covered sufficiently for 

the purchaser’s purposes, the matter should be referred to the local Southern States 

Representative. 
The contents of this instruction manual should not become part of or modify any prior or existing 

agreement, commitment or relationship. The sales contract contains the entire obligations of 

Southern States. The Warranty contained in the contract between the parties is the sole warranty 

of Southern States. Any statements contained herein do not create new warranties or modify the 

existing warranty. 

 

 

Important 

 

The information contained herein is general in nature and not intended for specific application 

purposes.  It does not relieve the user of responsibility to use sound practices in application, 

installation, operation, and maintenance of the equipment purchased.  Southern States reserves 

the right to make changes in the specifications shown herein or to make improvements at any time 

without notice or obligations.  Should a conflict arise between the general information contained in 

this publication and the contents of drawings or supplementary material, or both, the latter shall 

take precedence. 

 

 

Summary of Contents for COLE L





























Reviews: