background image

6

Unplug this apparatus during lightning storms or when unused

for long periods of time.

Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way

such as, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or

moisture, the apparatus does not operate normally or has

been dropped.

If the power cord is damaged obtain a replacement from your

Soundcraft dealer.

It is recommended that all maintenance and service on the

product should be carried out by Soundcraft or its authorised

agents. Soundcraft cannot accept any liability whatsoever

for any loss or damage caused by service, maintenance or

repair by unauthorised personnel.

If a trolley is used, use caution when moving the trolley /

apparatus combination to avoid injury from tip-over.

WARNINGS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

This unit contains no user serviceable parts.  Refer all servicing

to a qualified service engineer, through the appropriate

Soundcraft dealer.

Clean the apparatus only with a dry cloth.

DO NOT block any of the ventilation openings. DO NOT install

where air cannot flow over the rear of the unit.  DO Install in

accordance with the manufacturers instructions.

Summary of Contents for GIGRAC 1000st

































Reviews: