background image

20

(15) Amp Clip LEDs

The red Amp Clip LEDs illuminate when the input levels to the internal

amplifiers are too high.  It is acceptable for these LEDs to come on

momentarily every now and then but the Main or Monitor Master Volume

(depending on which signals have been routed to the amplifiers: see

(16)

 below) should be turned down if the Amp Clip LEDs illuminate

consistently.

NB!  Continued use of the GigRac with the Amp Clip

LED illuminated could cause serious damage to your

GigRac and your loudspeakers!

(16) Internal Amplifier Source Select Switch

This switch determines which signals are routed to the internal power

amplifiers.  The options are: Main L to amp 1, and Main R to amp 2, or,

Main L + R to amp1, and monitor to amp 2.  See the diagram opposite.

(17) Main Output Meters

The dual 10-segment output meters show the signal levels  being fed to

the internal power amplifiers.  See 

(16)

 above.

It is best to aim to have the red 10dB LEDs lighting up regularly during

the loudest signals peaks playing through your GigRac and the 16dB

LEDs flicking on very occasionally.  This will ensure that a good level is

passing through the mixer.

(18) Record Outputs

The Record Outputs (L & R) are for connecting a recording device such

as a cassette or mini disk recorder.

The signal output at the Record Output sockets is a post fade signal

derived from the Main Mix outputs.  The amount of signal level leaving

the GigRac via the Record Outputs is determined by the Main Master

Volume control 

(10)

.

(19) Playback In

The Playback In connectors allow you to playback from your recording

device through the Main outputs/Speakers/Headphones. A useful tip is

to press the standby mute switch 

(20)

, this mutes all other inputs to

Summary of Contents for GIGRAC 1000st

































Reviews: