Sound Devices 774T, User Manual And Technical Information

Page: 60 / 82

744T User Guide and Technical Information
58
v. 2.09 Features and specifications are subject to change. Visit www.sounddevices.com for the latest documentation.
# Setup Name Setup Description Setup Options
10 Rec: Take Reset Mode Defines when take numbers are reset. Reset
brings take number to <1>. • Never
- take numbers do not reset
• When scene is changed
- take resets when scene name is changed
• When daily folder changes
- takes reset on new day
• Either scene or daily
- takes reset on either change
11 Rec: Pre-Roll Time Selects the amount of pre-roll time the 744T
will add to the beginning of each file. 0–10 sec. @ 48 kHz
0–5 sec. @ 88.2–96.096 kHz
0–2 sec. @ >96.096–192 kHz
12
Rec: Dither
Selects whether to dither is added to 24 bit
digital signals while recording 16 bit files. • Off
• On (16 bit only)
13 Rec: Timer Start Sets a specific start time/date for unattended
recording. Unit must be powered. <enter time, date>
14 Rec: Timer Stop Set a specific time/date to stop recording.
May be used with or without the Rec: Timer
Start. May be set before the Timer Start time
to temporarily stop recording and then resume
recording with Timer Start. <enter time, date>
15 Rec: Error Handler Sets the behavior when a hard drive write
error occurs. • Stop recording
• Keep Recording to New File
16 Rec: Record Indicator Sets how the large display looks when the unit
enters record. • Normal Numbers
• Reverse Numbers
• Flash Numbers
17 Input: Routing Allows the user to setup their routing matrix
among all available inputs and tracks. There
are preset routings and three custom routings
available. Pressing the input select key repeat-
edly will cycle through all preset routings.
Primarily accessible from the Input Select Key.
• 1
➞
A / 2
➞
B
• 1
➞
A / 1
➞
B
• 1
➞
A,B / 2
➞
A,B
• 1
➞
A / 2
➞
B / 3
➞
C / 4
➞
D
• 1,2,3
➞
A / 1
➞
B / 2
➞
C / 3
➞
D
• 1
➞
A,C / 2
➞
B,D
• 3
➞
C / 4
➞
D
• Custom Route 1
• Custom Route 2
• Custom Route 3
18
19 Input 1: 48V Phantom
Input 2: 48V Phantom Enables or disables 48 V phantom power on
inputs 1 and 2. • Off
• On - Mic
• On - Mic and Line
20 Mic Inputs: Limiter Enables or disables the analog input limiter on
input 1 and 2 mic preamps. • Disabled
• Enabled
21
22 Mic Input 1: Low Cut
Mic Input 2: Low Cut Enables the high-pass (low cut) filter to reduce
sensitivity to low frequencies. • Disabled
• Enabled
23
24 Mic Input 1: Low Cut Freq
Mic Input 2: Low Cut Freq Selection of twelve high-pass filter frequency
and slope combinations for microphone inputs. • 40, • 80, • 160, • 240 Hz @ 12 dB/oct
• 40, • 80, • 160, • 240 Hz @ 18 dB/oct
• 40, • 80, • 160, • 240 Hz @ 24 dB/oct
25
26
Mic Input 1: Gain Range
Mic Input 2: Gain Range
Selects the sensitivity of the microphone input.
Low sensitivity is used for very loud and/or
very hot microphones. • Normal
• Low
27
28 Input 1, 2: Source
Input 3, 4: Source Forces the inputs to analog or digital mode.
Default is auto-select. • Auto-select
• Analog
• Digital (S/PDIF/AES)
• Disabled (Power Save)