Sorvall TC6 Service Manual Download Page 90

Page: 90 / 109

TC6

Troubleshooting

6-5

Table 6-1. TC6

Troubleshooting Chart (continued)

Problem

Probable Cause

Solution

2. Shorted RUN command on

Control Printed Circuit Board.

3. Loss of bit in timing string.

4. Loss of tach signal.

5. Shorted RUN command on

Motor Control Printed Circuit
Board.

6. Speed control stuck at maxi-

mum.

7. Loss of tach input.

1. Output transistor problem on

Motor Control Printed Circuit
Board.

1. START switch stuck ON.

2. STOP switch stuck OFF.

3. Shorted RUN command line.

4. Speed Control stuck at maxi-

mum.

1. Rotor/load out of balance.

1. Replace Control Printed

Circuit Board.

2. Replace Control Printed

Circuit Board.

3. Replace Control Printed

Circuit Board.

4. a. Replace Control Printed

Circuit Board.

b. Replace Motor Control

Printed Circuit Board.

c. Replace motor.

5. Replace Motor Control

Printed Circuit Board.

6. Replace Motor Control

Printed Circuit Board.

7. Replace the Motor Control

Printed Circuit Board.

1. Replace the Motor Control

Printed Circuit Board.

1. Replace switch.

2. Replace switch.

3. a. Defective Motor Control

Printed Circuit Board. Re-
place board.

b. Defective Control Printed

Circuit Board. Replace
board.

4. a. Defective Motor Control

Printed Circuit Board.
Replace board.

b. Defective Control Printed

Circuit Board. Replace
board.

Rotor will not reach top speed.

Rotor exceeds set speed.

Rotor speed erratic.

Unable to stop rotor.

Summary of Contents for TC6














































































































Search results

Summary of Contents for TC6

Reviews:

Brands by name

Popular brands

Sorvall TC6, Service Manual

Search results

Summary of Contents for TC6

Reviews:

Brands by name

Popular brands