Sorvall TC6 Service Manual Download Page 109

Page: 109 / 109

In the United States, to

place an Order, or for Applications or

Technical Information, call

TOLL FREE

1-800-522-SPIN

(1-800-522-7746)

SORVALL CUSTOMER SERVICE
31 Pecks Lane
Newtown, CT 06470-2337
FAX: (203) 270-2166

(203) 270-2210

For Ordering Information or to place an Order,
contact:

For Applications Information, or for Technical
or Service Information, contact either:

The SORVALL APPLICATIONS LAB,
or SORVALL SERVICE & SUPPORT
31 Pecks Lane
Newtown, CT 06470-2337
FAX: (203) 270-2115

Other countries, including
CANADA, LATIN AMERICA,
ASIA PACIFIC, or JAPAN:

SORVALL International Sales
31 Pecks Lane
Newtown, CT 06470-2337
U.S.A.
Telephone: (203) 270-2080
FAX: (203) 270-2210

(203) 270-2166

Or contact your local
representative for
SORVALL

products.

FRANCE:

SORVALL (France) SA
LP 912
LES CONQUERANTS
1 avenue de l'Atlantique
Les Ulis
91976 COURTABOEUF Cedex
Téléphone: 01 69 18 77 77
FAX: 01 60 92 00 34

Other EUROPE, AFRICA,
or MIDDLE EAST:

SORVALL International Sales
International Centre
Boulton Road, Stevenage
Hertfordshire SG1 4QX
UNITED KINGDOM
Telephone: 44 (1438) 342900
FAX: 44 (1438) 342925

Or contact your local
representative for
SORVALL

products.

Rev. 3/97

UNITED KINGDOM:

SORVALL (UK) Limited
International Centre
Boulton Road, Stevenage
Hertfordshire SG1 4QX
Telephone: (01438) 342911
FAX: (01438) 342915

FEDERAL REPUBLIC
of GERMANY:

SORVALL (Deutschland) GmbH
DuPont Strasse 1
61352 Bad Homburg v.d.H.
Telefon: 6172/87-2544
FAX: 6172/87-2547

ITALY:

SORVALL (Italiana) Srl
Via A. Volta N. 16
20093 Cologno Monzese (MI)
Telefono: 02/25302372
FAX: 02/2540526

Summary of Contents for TC6














































































































Search results

Summary of Contents for TC6

Reviews:

Brands by name

Popular brands

Sorvall TC6, Service Manual

Search results

Summary of Contents for TC6

Reviews:

Brands by name

Popular brands