Sorvall TC6 Service Manual Download Page 74

Page: 74 / 109

TC6

Repair and Replacement

5-7

5-6. Door Closed Sensor
Replacement

NOTE

Before you replace the door closed sensor, be sure it is
functioning properly by following the procedure given in
paragraph 5-5. Also, check the

new sensor before

installing.

1. Turn the centrifuge power OFF and unplug the power cord.

2. Remove the two phillips screws located on each side of the

bezel. Carefully lift the bezel up to disengage it from the frame
(but do not disconnect wiring) and gently place the bezel so that
the p.c. boards are facing up.

3. Disconnect P/J 331 (refer to figure 5-2). Loosen the back-up nut.

Then, while holding the back-up nut, remove and discard the
old door closed sensor threading it out through the

bottom

of the

bracket.

4. Open chamber door. Remove the sensor cover plug from the

cabinet.

Figure 5-2. Door Closed Sensor Parts Location

CHAMBER DOOR

MAGNET

TOP OF CABINET

SENSOR
COVER PLUG

DOOR CLOSED
SENSOR

BACK-UP NUT

SENSOR
BRACKET

CONNECTOR
P/J331

Summary of Contents for TC6














































































































Search results

Summary of Contents for TC6

Reviews:

Brands by name

Popular brands

Sorvall TC6, Service Manual

Search results

Summary of Contents for TC6

Reviews:

Brands by name

Popular brands