manualshive.com logo in svg

Sorel MTDC, Installation And Operating Instructions Manual, Page: 35 / 48

Share
Download
Sorel MTDC Installation And Operating Instructions Manual Download Page 35

35

Special functions

6.5.9. - Solid fuel boiler

The relay is used to control an additional solid fuel boiler.

R

el

ay

 fu

nc

tion

s

6.5.9.2. - SF Tmin

Minimum temperature in the solid fuel boiler to switch on the pump. If the tem-

perature at the boiler sensor is below this temperature, the relay is disabled.

6.5.9.3. - ∆ T Solid fuel

Switch on and Switch off condition for the temperature difference between boiler 

and storage. Switch on difference ∆ T SF

. 

Switch off temperature difference ∆ T 

SF.

6.5.9.4. - SF Tmax

Maximum temperature in the storage. If this is exceeded, the relay is switched 

off.

This determines the sensor, that is used as boiler sensor.

6.5.9.5. - Boiler sensor

This determines the sensor, that is used as storage sensor. 

6.5.9.6. - Storage sensor

6.5.10. - Error message

The relay is switched on, when one or more protective funtion is active or a 

message is shown. This function can be inverted, so that the relay is alway on 

and switches off when a protective function or a message is shown.  

Collector protection, System protection, Frost protection, Recooling,  

Anti-legionella protection, Messages, Collector alarm

6.5.11. - Booster pump

6.5.11.2. - Filling time

Additional pump that fills the system at the start of every solar charge.

Time the pump is switched on

This setting determines the length of time the pump is switched on at the start 

of a solar charge.

Summary of Contents for MTDC

















































Reviews:

No comments