manualshive.com logo in svg

Sorel MTDC, Installation And Operating Instructions Manual, Page: 26 / 48

Share
Download
Sorel MTDC Installation And Operating Instructions Manual Download Page 26

26

Special functions

6.3. - Speed control

6.3.1. -  Modes

The following speed variants are available here:

Off:

 There is no speed control. The connected pump is only switched on or off with full 

speed.

Mode 1:

 After the purging time the controller switches to the set max. speed. If the 

temperature difference Set ∆T between the reference sensors (collector and storage 

tank) is less than the set value, then the speed is decreased by one stage after the 

control time elapses. If the temperature difference between the reference sensors is 

greater than the set value, then the speed is increased by one stage after the control 

time elapses. If the controller has adjusted the speed of the pump down to the smallest 

stage and the Set ∆T between the reference sensors is ∆T off, the pump is switched 

off.

Mode 2:

 After the purging time the controller switches to the set min. speed.  If the 

temperature difference Set ∆T between the reference sensors (collector and storage 

tank) is greater than the set value, then the speed is increased by one stage after the 

control time elapses. If the temperature difference Set ∆T between the reference sen-

sors is below the set value, then the speed is decreased by one stage after the control 

time elapses. If the controller has adjusted the speed of the pump down to the smallest 

stage and the ∆T between the reference sensors is T∆off, the pump is switched off.

Mode 3:

 After the purging time the controller switches to the set min. speed.  If the 

temperature at the reference sensor (collector) is greater than the setpoint to be set 

subsequently, then the speed is increased by one stage after the control time expires. 

If the temperature at the reference sensor (collector) is less than the setpoint to be set 

subsequently, then the speed is decreased by one stage after the control time expires.

Mode 4: 

When the primary storage is loaded, speed control works as in V3.

When the secondary storage is loaded, speed control works as in V2.

With speed control the MTDC

   makes it possible to vary the speed of connected 

pumps.

This function should only be activated by a specialist. Depending on the 

pump and pump stage used, the minimum speed should not be set too 

low, because otherwise the pump or the system may be damaged. The 

information provided by the relevant manufacturer must also be observed! 

If in doubt, the min. speed and the pump stage should generally be set to 

high rather than too low.

Caution

Summary of Contents for MTDC

















































Reviews:

No comments