Sony WRR-862A, Service Manual, Page: 28 / 96

3-14
WRR-862A/862B
RF
LCD : LED :
Red
Green
RF
LCD : LED :
Green
RF
LCD : LED :
Green
RF
LCD : LED :
(5) Increase gradually the output level from the signal gen-
erator, and check that the output level of the signal gen-
erator is as follows when the RF input level indicator
lights.
RF level indicator Signal generator
lights in output level
20 dB
u
V
EMFM
±
5 dB
30 dB u V
EMFM
±
5 dB
40 dB u V
EMFM
±
5 dB
50 dB u V
EMFM
±
5 dB
(6) Set the channel setting and FREQUENCY (carrier fre-
quency) of the signal generator as shown
1
and
2
below.
Perform the procedures (3) through (5) above, for each
channel setting (
1
and
2
).
1
Channel setting :
CE21 model : Group 00, 2101 channel (470.125 MHz)
CE33 model : Group 00, 3301 channel (566.125 MHz)
CE62 model : Group 00, 6201 channel (798.125 MHz)
CE67 model : Group 00, 6701 channel (838.125 MHz)
U1416 model : Group 00, 1401 channel (470.125 MHz)
U3032 model : Group 00, 3001 channel (566.125 MHz)
U4244 model : Group 00, 4201 channel (638.125 MHz)
U6264 model : Group 00, 6201 channel (758.125 MHz)
U6668 model : Group 00, 6601 channel (782.125 MHz)
AU66 model : Group 00, 6601 channel (792.250 MHz)
Signal generator setting
FREQUENCY(Carrier frequency):
CE21 model : 470.125 MHz
CE33 model : 566.125 MHz
CE62 model : 798.125 MHz
CE67 model : 838.125 MHz
U1416 model : 470.125 MHz
U3032 model : 566.125 MHz
U4244 model : 638.125 MHz
U6264 model : 758.125 MHz
U6668 model : 782.125 MHz
AU66 model : 792.250 MHz
3-2-9. RF Level Indicator Check
n
Perform this adjustment/check with the case (upper) , parti-
tion and battery case installed.
(Do under the regular use condition).
Equipment and Tools Required
Same as “3-2-5. S/N Checking”.
Connection
Same as “3-2-5. S/N Checking”.
Switch and Control Setting
Same as “1. Switch and Control Initial Setting” on page 3-2
expect the following setting.
SQUELCH switch : ON
(Set the RF squelch level to “10” )
Procedure
Step 1. Tuner 1 Checking
(1) Set the CONTROL switch (S1601) to “1”.
(2) Set the channel setting as follows;
.
Tuner 1 channel setting
Same as “1. Switch and Control Initial Setting” on
page 3-2.
n
Set the Tuner 2 to channel setting different from the
above Tuner 1 channel setting.
(3) Connect the signal generator to the ANT a connector.
(4) Set the signal generator as follows:
FREQUENCY(Carrier frequency):
CE21 model : 482.000 MHz
CE33 model : 578.000 MHz
CE62 model : 810.000 MHz
CE67 model : 850.000 MHz
U1416 model : 482.125 MHz
U3032 model : 578.125 MHz
U4244 model : 650.125 MHz
U6264 model : 770.125 MHz
U6668 model : 794.125 MHz
AU66 model : 799.250 MHz
RF OUTPUT (Output level) : 10 dB
u
V
EMF
( =
_
103 dBm)
MODULATION (Modulation frequency) :
OFF (No modulation)