manualshive.com logo in svg

Sony SVT-RA168, Service Manual

Share
Download
Sony SVT-RA168 Service Manual Download Page 16

1-6

SVT-RA40/RA168

1-5. Circuit Board Locations

CP-1 PWB Assembly

TM-1 PWB

TM-2 PWB

PW-1 PWB

CT-1 PWB
(Option for SVT-RS100)

Soldered

CP-1 PWB assembly

Battery

1-6. Lithium Battery for Backup

This unit is equipped with a backup battery(lithium

battery) to maintain the clock settings.

For replacement, be sure to use the specified part.

Replacement part: Z3901/CP-1 board

Part description:

MnO2-Li (lithium battery)

Part No.:

1-756-091-11

Replacement

1.

Remove the cabinet and bottom cover. (Refer to

Section 1-2-1.Removing the Cabinet Parts)

2.

Place the mechanism unit and CP-1 board up side

down as a whole on a flat surface with foil side of the

CP-1 board facing up. (Refer to Section 1-3.Tempo-

rarily Setting Up and Connecting CP-1 PWB Assem-

bly)

3.

Unsolder the leads of the battery from the soldering

side of the CP-1 board and remove the battery.

Solder the backup battery in the reverse procedure of

removal.

Summary of Contents for SVT-RA168





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands