manualshive.com logo in svg

Sony SVT-RA168, Service Manual

Share
Download
Sony SVT-RA168 Service Manual Download Page 10

6

SVT-RA40/RA168

Contents

This service manual is organized by following sections.

Section 1

Service Overview

Describes the information that is required to service (maintenance table on the

monitor screen, removal of cabinet, mechanism unit and main board, circuit board

locations, etc.).

Section 2

Mechanical Adjustments

Describes the recommended periodic maintenance, the cleaning procedure, service

tools, disassembling the main parts of the mechanism and tape path adjustment.

Section 3

Electrical Adjustments

Describes the electrical alignment for the maintenance of this unit.

Section 4

Spare Parts

Describes the exploded views, the mechanical parts list and the electrical parts list.

Section 5

Semiconductors

Describes information on semiconductors used for unit.

Section 6

Block Diagrams

Describes the overall wiring and the block diagrams of each board.

Section 7

Schematic Diagrams

Describes the schematic diagrams for the unit.

Section 8

Board Layouts

Describes the board layouts for the unit.

Summary of Contents for SVT-RA168





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands