SPP Q110/Q120 3 856 344 21 E F
Mounting your phone on the wall
1
Remove the hang-up tab.
2
Reverse the hang-up tab and insert it back.
3
Attach the telephone line cord and AC power adaptor cord to the
base unit.
Use the shorter cord for mounting.
4
Plug the telephone line cord into the telephone outlet, and hook the
base unit to the wall plate as illustrated. Then fully extend the
antenna.
To change a stored number
Store a new number, as described previously.
Making calls with speed dialing
1
Press
(TALK)
and wait until the TALK/BATT LOW lamp lights up.
The dialing keys light up (SPP-Q120 only).
2
Press
(SPEED DIAL)
.
3
Enter the desired speed dialing number (
(0)
to
(9)
).
The phone number stored in the speed dialing number will be dialed.
Resetting the digital security code
The first time you charge the battery pack, a random security code is
automatically assigned between the base unit and the handset. Only a handset
which has this security code can make calls through the base unit. This system
prevents the possibility of other cordless telephone handsets making calls
through your base unit. You normally do not need to reset the security code.
However, in the unlikely event that you suspect that another cordless phone uses
the same security code, you can manually change the code. Pick up the handset
from the base unit, and proceed as follows:
1
Press
(PGM)
.
The TALK/BATT LOW lamp flashes.
2
Press
(#)
.
You hear a confirmation beep.
The dialing keys light up (SPP-Q120
only).
3
Press three of the dialing keys (001 to
999) to store a new code.
4
Press
(PGM)
.
You hear a long confirmation beep
and the TALK/BATT LOW lamp
goes off.
5
Immediately replace the handset on
the base unit
You hear a long confirmation beep
and the phone stores the new code.
Note
If the battery pack in the handset is completely discharged, or is removed
from the handset for more than several seconds, the digital security code
stored will be lost. If this happens, charge the battery pack and a new
security code will be automatically assigned.
Tip
This procedure will change the code in both the base unit and the handset.
The code can be changed as often as desired.
Paging
You can page the handset from the base unit. Note that you can’t
page if the handset is in use.
To page
Press
(PAGE)
.
The handset rings.
When you keep pressing
(PAGE)
,
the handset rings continuously.
Maintenance
• Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the
cabinet.
• If the charge terminals of the base unit and handset are soiled, wipe them with
a soft cloth or paper.
If you have any questions or problems concerning your phone, please consult
your nearest Sony dealer.
General
Frequency control
Crystal-controlled PLL
Operation mode
FM, duplex
Operation channel
25 channels
Supplied accessories
AC power adaptor AC-T56 (1)
Telephone line cords (2)
Rechargeable battery pack BP-T16 (1)
Directories (2 sheets)
Handset
Power source
Rechargeable battery pack BP-T16
Battery life
Standby: Approx. 14 days
Talk: Approx. 6 hours
Dimensions
Approx. 59 x 201 x 59 mm (w/h/d), antenna
excluded (Approx. 2
3
⁄
8
x 8 x 2
3
⁄
8
inches)
Antenna: 110 mm (4
3
⁄
8
inches)
Mass
Approx. 230 g (Approx. 8.1 oz), battery included
Base unit
Power source
DC 9V from AC power adaptor
Battery charging time
Approx. 12 hours
Dimensions
Approx. 148 x 58 x 233 mm (w/h/d), antenna
excluded (Approx. 5
7
⁄
8
x 2
3
⁄
8
x 9
1
⁄
4
inches)
Antenna: 430 mm (17 inches)
Mass
Approx. 345 g (Approx. 12.1 oz)
Design and specifications are subject to change without notice.
TALK/BATT
LOW Lamp
1, 2
3
4
Wall plate
Troubleshooting
Problem
Solution
The handset does not make or
receive a call.
• Reset the digital security code.
• Place the base unit away from noise sources
such as TV, FM radio or PC.
• Make sure the base unit is connected to an AC
outlet.
• The battery pack may be discharged. Charge
the battery pack for about 12 hours.
You hear no dial tone.
• Make sure the telephone line cord is securely
connected to the telephone outlet.
The handset doesn’t connect at
all, even the numbers you dial
are correct.
• Make sure the dial mode setting (pulse or tone)
is correct.
The handset does not redial
correctly.
• Make sure the number (including the tone and
pause digits, if used) you last dialed is less
than 32 digits.
The handset does not make a
speed dialing call.
• Make sure there is a phone number correctly
stored in the speed dialing.
• Store the desired phone number once more.
The handset does not ring.
• Make sure the base unit is connected to an AC
outlet.
• The battery may have little or no power.
Charge the battery for more than 12 hours.
• Extend the antenna of the base unit vertically.
• Place the base unit away from noise sources.
The handset does not ring
when paging from the base
unit.
You hear a beep every 3
seconds and the TALK/BATT
LOW lamp flashes.
• Charge the battery pack for about 12 hours.
Specification
