Sony SPP-A985 - Cordless Telephone With Answering System Operating Instructions Manual Download

Page: 69 / 80

Additional Information

Additional Information

Mounting the base phone on a wall

Raise the hang-up tab.

Plug the telephone line cord to
the LINE jack and the AC power
adaptor to the DC IN 9V jack,
and hook the cords. Use the
shorter cord for mounting.

Attach the wall bracket to the
center of the base phone.

Align the

marks of the wall

bracket with those of the base
phone.

Plug the telephone line cord to
the telephone outlet, and hook
the base phone to the wall plate.

Plug the AC power adaptor to
an AC outlet. Then raise the
antenna so that it points
towards the ceiling.

Tip

To remove the wall bracket, press the lower tabs.

Additional Information

4,5

Telephone
line cord

Wall
bracket

Hang-up tab

Telephone
line cord

AC power
adaptor

AC power
adaptor cord

Wall
plate

AC outlet

Summary of Contents for SPP-A985 - Cordless Telephone With Answering System

















































































Search results

Summary of Contents for SPP-A985 - Cordless Telephone With Answering System

Reviews:

Related manuals for SPP-A985 - Cordless Telephone With Answering System

Brands by name

Popular brands

Sony SPP-A985 - Cordless Telephone With Answering System, Operating Instructions Manual

Search results

Summary of Contents for SPP-A985 - Cordless Telephone With Answering System

Reviews:

Related manuals for SPP-A985 - Cordless Telephone With Answering System

Brands by name

Popular brands