Sony SPP-A985 - Cordless Telephone With Answering System Page 12 Operating Instructions Manual Download

Page: 12 / 80

Getting Started

Notes

• Use only the supplied AC-T131 AC power adaptor.

Do not use any other AC power adaptor.

• Connect the AC power adaptor to a continuous power

supply.

• Place the base phone close to the AC outlet so that

you can unplug the AC power adaptor easily.

Tip

If your telephone outlet is not modular, contact your
telephone service company for assistance.

Choose the dialing mode

For the telephone to work properly, select an appropriate dialing mode
(tone or pulse).

Depending on your dialing system, set the DIAL MODE switch as
follows:

If your dialing system is

Set the switch to

Tone

TONE

Pulse

PULSE

If you aren't sure of your dialing system

Make a trial call with the DIAL MODE switch set to TONE.
If the call connects, leave the switch as is; otherwise, set to PULSE.

Polarity of the plug

Step 2: Setting up the base phone (continued)

DIAL MODE
switch

Modular

–

Summary of Contents for SPP-A985 - Cordless Telephone With Answering System

















































































Search results

Summary of Contents for SPP-A985 - Cordless Telephone With Answering System

Reviews:

Related manuals for SPP-A985 - Cordless Telephone With Answering System

Brands by name

Popular brands

Sony SPP-A985 - Cordless Telephone With Answering System, Operating Instructions Manual

Search results

Summary of Contents for SPP-A985 - Cordless Telephone With Answering System

Reviews:

Related manuals for SPP-A985 - Cordless Telephone With Answering System

Brands by name

Popular brands