Sony SAITe1300-F Operating Instructions Manual Download Page 19 | Manualshive

Page: 19 / 50

background image

19

Chapter 2 Installation

Setting the DIP Switches

By setting the DIP switches at the bottom of the S-AIT Tape Drive Unit, you
can:
• Choose whether to compress the data when recording.
• Choose whether the host can control data compression.

The default settings of the DIP switches is as follows.
• DC Control-1: ON

Compression is enabled.

• DC Control-2: OFF

The host can control compression.

If necessary, change the settings as follows

Caution

Before removing the access cover to change DIP switch settings of the S-AIT
Tape Drive Unit, turn off the unit and disconnect the power cable.

1

Make sure that the unit is off.

2

Remove the two screws with a screwdriver and remove the access cover

Screw

Access cover

DIP switches

«
...
17
18
19
20
21
...
»

Summary of Contents for SAITe1300-F



















































Reviews:

No comments

Related manuals for SAITe1300-F

Brand: Samsung Pages: 14

Brand: Samsung Pages: 14

Brand: Samsung Pages: 4

Brand: XenData Pages: 12

Brand: Gardiun Pages: 27

Brand: Quantum Pages: 9

Brand: Quantum Pages: 2

Brand: Quantum Pages: 11

Brand: Quantum Pages: 7

Brand: Quantum Pages: 10

Brand: Quantum Pages: 8

Brand: Tandberg Data Pages: 58

ValueLoader DLT VS80

Brand: Quantum Pages: 50

Brand: Quantum Pages: 42

Brand: Quantum Pages: 148

Brand: QNAP Pages: 24

454L / 120 US GAL

Brand: Keter Pages: 12

RS-1600-FC-FFX2

Brand: Xyratex Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands