Sony SAITe1300-F Operating Instructions Manual Download Page 29 | Manualshive

Page: 29 / 50

background image

29

Chapter 2 Installation

Connecting the Optical Fiber Cable for Fibre Channel
(SAITe1300-F only)

The SAITe1300-F is equipped with an interface that complies with the Fibre
Channel standards with the following specifications.
• Short-wave laser
• 200 MB/sec
• Duplex LC Fibre Channel connectors

The equipment (HBA, hub, switch, etc.) to be connected to the SAITe1300-F
must be of the same type.

Use an optical fiber cable with the following specifications.
• Duplex LC Fibre Channel connectors
• 50/125

µ

m multimode optical fiber cable

Caution

• If your interface and optical fiber cable are different types, the unit may not

operate correctly when connected.

• Turn off the unit when connecting or disconnecting a cable to the fibre

channel connector. Failing to do so may result in damage.

• Never touch the fibre channel connector of the unit when the unit is on. Doing

so may result in damage.

Host computer

or

HUB, switch, etc.

FIBRE CHANNEL

FIBRE CHANNEL

Host bus adaptor
(FC HBA)

Optical fiber
cable for fibre
channel*

Optical fiber cable for fibre channel*

FIBRE CHANNEL

* 50/125

µ

m, MMF, Duplex LC

«
...
27
28
29
30
31
...
»

Summary of Contents for SAITe1300-F



















































Reviews:

No comments

Related manuals for SAITe1300-F

Brand: R/Evolution Pages: 58

Camedia MAUSB-100

Brand: Olympus Pages: 2

TrueNAS R Series

Brand: iXsystems Pages: 24

Brand: Transcend Pages: 24

Brand: Swiss Aqua Technologies Pages: 5

Brand: ATI Technologies Pages: 24

Brand: Qualstar Pages: 8

Brand: Aegis Pages: 1

AccessPoint 001890

Brand: GE Pages: 2

Digital Video Storage System

Brand: GE Pages: 24

Monogram ZWVS1000SR

Brand: GE Pages: 40

Brand: morse Pages: 11

Brand: Kanguru Pages: 22

Brand: Viking Pages: 33

Brand: Verbatim Pages: 72

Brand: XtendLan Pages: 34

Brand: ClearSpan Pages: 25

Brand: OLT Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands