Sony PCWA-C500 - Wireless Lan Pc Card Operating Instructions Manual Download Page 56

Page: 56 / 64

Specifications

Protocol support

TCP/IP compliant

Standard

IEEE802.11a/IEEE802.11

Radio frequency

5.15 to 5.35 GHz

Modulation method

OFDM (IEEE802.11a compliant)

General

Power requirements

3.3 V DC (supplied from the computer

through the PC card adapter)

Current

Peak current at transmission: 560 mA

Peak current at reception: 400 mA

Connector

PC Card CardBus

Dimensions

Approx. 4.7

0.2

2.2 inches

(Approx. 119

54 mm ) (w/h/d)

(Antenna height: 0.5 inches (Approx. 10.4 mm))

Mass

Approx. 1.8 oz (Approx. 50 g)

Operating temperature

41°F to 95°F (5°C to 35°C) (not condensed)

Environment temperature

-4°F to 140°F (-20°C to 60°C) (not

condensed)

Supplied accessories

See “Unpacking” on page 11.

Design and specifications are subject to change

without notice.

Getting help

This section describes how to get help and
support from Sony, as well as
troubleshooting tips for your Wireless
LAN PC Card.

About Sony’s Support Options

Sony provides several support options for
your Wireless LAN PC Card.

❒

This Operating Instructions

explains how to use your Wireless LAN
PC Card.

❒

Quick Start Guide

explains how to

install the Wireless LAN PC Card,
Wireless LAN PC Card driver, and the
Wireless Panel utility software
provided.

❒

Wireless Panel Online Help

explains how to use the Wireless Panel
utility software provided.

❒

The Sony Wireless LAN PC Card
support Web site
http://www.sony.com/
wirelesslansupport/

provides the

latest information on your Wireless
LAN PC Card.

❒

The Sony e-mail support service

answers your questions by electronic
mail. Just send your question in an e-
mail message and a customer service
representative will reply. To send a
question to Sony e-mail support, fill out
the e-mail form at

http://www.sony.com/
wirelesslansupport/

Summary of Contents for PCWA-C500 - Wireless Lan Pc Card

































































Search results

Summary of Contents for PCWA-C500 - Wireless Lan Pc Card

Reviews:

Related manuals for PCWA-C500 - Wireless Lan Pc Card

Brands by name

Popular brands

Sony PCWA-C500 - Wireless Lan Pc Card, Operating Instructions Manual

Search results

Summary of Contents for PCWA-C500 - Wireless Lan Pc Card

Reviews:

Related manuals for PCWA-C500 - Wireless Lan Pc Card

Brands by name

Popular brands