54
Tele-File System
Chapt
er
3
Re
c
o
rdin
g and Pl
a
y
b
a
c
k
Clearing recorded data
1
Follow steps
1
to
4
in
“Confirming the remaining
capacity on the memory label” (page 53)
until the
TELE FILE page of the FILE menu is displayed on the
viewfinder screen.
2
Turn the MENU knob to move
b
mark to TELE FILE
CLEAR, then push the MENU knob.
The message CLEAR OK? YES NO appears. In this
case, the
b
mark is displayed for NO and NO flashes.
3
Turn the MENU knob to move
b
mark to YES (YES
flashes), then push the MENU knob.
The data recorded on the memory label is cleared.
“100%” appears at the REMAIN column.
• When the memory label is protected from accidental
erasure, you cannot clear recorded data.
• The time code data is cleared. However, the memory
label ID is not cleared.
3-4-2 Recording a Tele-File Mark
The Tele-File mark, that is a rating of the images recorded
just before they are recorded, can be recorded onto the
memory label with the recording start time code, every
time the unit enter the rec pause mode.
The following three kinds of Tele-File marks are available:
•
OK:
Place this mark when you decide the recorded
images are good.
•
NG:
Place this mark when you decide the recorded
images are not good.
•
KP:
Place this mark when it is hard to decide whether or
not the recorded images are good just after recording, or
when you want to insert a mark between multiple shots.
Recorded Tele-File marks are read by studio-use devices,
logging software, and so on, which support the Tele-File
function. These marks are very helpful for improving the
efficiency of tape editing.
To use this function, the TELE-FILE MARK function
should be assigned to the ASSIGN 1 switch.
For details, see “5-3-5 Assigning Functions to Assignable
Switches” on page 95.
Recording a Tele-File mark (OK/NG/KP)
onto the memory label
Follow the procedure below to record Tele-File marks
while shooting.
1
Start recording and set the unit to rec pause mode by
pushing the VTR START button or the VTR button on
the lens.
2
Push the ASSIGN 1 switch and select the appropriate
mark from among OK, NG, KP or ERASE.
Push the ASSIGN 1 switch several times until the
appropriate marks appears on the viewfinder.
When the display disappears from the viewfinder, the
selected mark is recorded with the recording start time
and one of the following messages appears on the
viewfinder.
If the display disappears before you selected the
appropriate mark
Repeat pushing the ASSIGN 1 switch until the desired
mark appears. If the desired mark disappears from the
viewfinder while that mark is displayed, the mark recorded
before will be overwritten and the mark newly displayed is
recorded.
The Tele-File marks are recorded only when they are
recorded using the ASSIGN 1 switch to which this
function is applied.
If you perform normal operations for starting recording
and entering in rec pause mode, the unit activates the
Notes
TELE FILE CLEAR : EXEC
TELE FILE MARK : OK
ID:
SIZE : 1KBYTE
REMAIN : 100%
STATUS : STANDBY
?F10 TELE FILE TOP
CLEAR OK? YES NO
TELE FILE CLEAR : EXEC
TELE FILE MARK : OK
ID:
SIZE : 1KBYTE
REMAIN : 100%
STATUS : STANDBY
F10 TELE FILE TOP
Note
Message
Meaning
TELE-FILE MARK: OK States that an OK mark has
been recorded.
TELE-FILE MARK: NG States that an NG mark has
been recorded.
TELE-FILE MARK: KP
States that a KP mark has
been recorded.
TELE-FILE MARK:
ERASE
States that a Tele-File mark
recorded on that shot has
been cancelled.
Note
Summary of Contents for MSV-970
Page 5: ...5 ...
Page 168: ...168 Index Index ...
Page 170: ...Sony Corporation MSW 970 970P SY 3 863 920 03 1 Printed in Japan 2006 11 13 2005 ...
