MEX-N5100BE/N5100BT/N5150BT
MEX-N5100BE/N5100BT/N5150BT
31
31
• Waveforms
– MAIN Board –
For Schematic Diagrams.
Note:
• All capacitors are in
μ
F unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in
Ω
and 1/4 W or less unless otherwise
speci
fi
ed.
•
f
: Internal component.
•
C
: Panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
•
A
: B+ Line.
• Power voltages is dc 14.4V and fed with regulated dc
power supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM)
[ ] : TUNER (AM)
( ) : CD PLAY
*
: Impossible to measure
• Voltages are taken with VOM (Input impedance 10 M
).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
:
AUDIO
f
:
TUNER
h
:
SIRIUSXM
J
: CD PLAY
d
:
USB
E
:
AUX
a
:
Bluetooth
N
:
MIC
For Printed Wiring Boards.
Note:
•
X
: Parts extracted from the component side.
•
Y
: Parts extracted from the conductor side.
•
f
: Internal component.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Note:
The components identi-
fi
ed by mark
0
or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number speci
fi
ed.
Note:
Les composants identi
fi
és
par une marque
0
sont
critiques pour la sécurité.
Ne les remplacer que par
une pièce portant le nu-
méro spéci
fi
é.
• Indication of transistor.
C
B
These are omitted.
E
Q
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note:
When the complete MAIN board is replaced, it is nec-
essary to replace knob (VOL) (SV) assy simultane-
ously. Also, the destination setting, Bluetooth operation
check and Bluetooth information writing is necessary.
Refer to “DESTINATION SETTING METHOD” on
page 4, “BLUETOOTH FUNCTION CHECKING
METHOD USING A CELLULAR PHONE” on page
7 and “BLUETOOTH INFORMATION WRITING
METHOD” on page 8.
Note:
When the complete MAIN board is replaced, it is nec-
essary to replace knob (VOL) (SV) assy simultane-
ously. Also, the destination setting, Bluetooth operation
check and Bluetooth information writing is necessary.
Refer to “DESTINATION SETTING METHOD” on
page 4, “BLUETOOTH FUNCTION CHECKING
METHOD USING A CELLULAR PHONE” on page
7 and “BLUETOOTH INFORMATION WRITING
METHOD” on page 8.
7
IC503
<zv/
(USB_X2)
50 mV/DIV, 10 ns/DIV
21 ns
180 mVp-p
22.8
P
s
3.5 Vp-p
2
IC705
rk
(PIO18)
1 V/DIV, 10
P
s/DIV
3
IC705
rl
(PIO19)
1 V/DIV, 200 ns/DIV
354 ns
3.5 Vp-p
4
IC705
yj
(XO)
1 V/DIV, 20 ns/DIV
59.6 ns
3.5 Vp-p
1
IC001
es
(XTAL_IN)
200 mV/DIV, 50 ns/DIV
83 ns
720 mVp-p
5
IC503
yk
(RTC_X2)
1 V/DIV, 20
P
s/DIV
30.8
P
s
1.8 Vp-p
6
IC503
ua
(XTAL)
1 V/DIV, 20 ns/DIV
75 ns
3.6 Vp-p
