manualshive.com logo in svg

Sony IPELA SNC-DM110, Service Manual

Share
Download
Sony IPELA SNC-DM110 Service Manual Download Page 10

1-4

SNC-DS10/DM110

Lens tube

Lens glass

Focus ring

PTPWH2 

x

 6

P2 

x

 5

CN103

Varifocal lens

Lens bracket

BI-222/224 board

Seal rubber

Filter

Harness

9.

Place the unit with the lens side down.

n

When placing the varifocal lens facing down, if the
lens glass protrudes from the end of the lens tube,

retract the lens glass by rotating the focus ring in the
direction of the arrow.

10. Disconnect the harness from the connector (CN103)

on the BI-222/224 board.

11. Remove the two screws (PTPWH2 

x

 6), then remove

the BI-222/224 board, seal rubber and filter.

12. Remove the three screws (P2 

x

 5), then remove the

lens bracket.

13. To install, reverse the removal procedure.

1-2-6. Cable Connection

m
.

For the indoor wiring (routing of cable from the side),

the lower case is provided with a knock-out type slit that
can be broken off using a tool such as plier.

By breaking off this slit, all cables including the supplied
I/O cable and audio cable can be routed from the side.

.

Only the LAN cable and power input cable are connect-
ed to this unit at the shipment.

LAN cable

Audio cable (Supplied)

BNC cable (Supplied)

Power input cable

I/O cable
 (Supplied)

Slit (knock-out type)

When performing the indoor wiring

Cable

SY-358 board

CN301

CN805

CN810

CN806

CN809

Summary of Contents for IPELA SNC-DM110

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands