8
Chapter 8 Connectors and Cables
160
HDC-900/950/930 Series Product Information Manual
B-Y/B OUT
R-Y/R OUT
VBS OUT
Connector Connector/cable
HKCU-953
FRAME REFERENCE IN
FRAME REFERENCE OUT
HDCU-950
1-569-370-12 PLUG, BNC or
RET IN (1-3)
BELDEN8281 Cable or
SERIAL OUTPUT (1-2,
MONI)
equivalent
SD SDI OUT (1-3)
HKCU-953
HD SDI OUT (1-2)
MIC1/MIC2(3-pin, Male)1-508-083-00 XLR 3-pin
female or CANNON XLR-3-
11C equivalent
MIC REMOTE (WF
REMTOE) (D-sub
15-pin, Female)
1-506-582-11 D-sub 15-pin,
male or JAE DA-CI-J10
equivalent
INTERCOM/TALLY/
PGM (D-sub 25-pin,
Female)
D-sub 25-pin, male
JAE DA-25PF-N equivalent
WF MODE (4-pin,
Female)
1-560-155-00 PLUG, 4-pin
male (supplied)
RCP/CNU (8-pin,
Female)
1-766-848-11 PLUG, 8-pin
male or CCA cable assembly
(optional)
CCA-5-30 (30 m), CCA-5-10
(10 m), CCA-5-3 (3 m)
INTERCOM (5-pin,
Female)
1-508-370-11 XLR 5-pin, male
or CANNON XLR-5-12C
equivalent
8-4.
CNU-700, Camera Command Network Unit
8-4-1
Connector Input/Output Signals
Main connector input and output signals are as
follows.
8-4-1-1
BNC connector 75 Ohms
[Input Signal]
REFERENCE
300 mV p-p, loop through
[Output Signal]
CHARACTER
700 mV p-p,
300 mV p-p (SYNC)
8-4-1-2
RS232C-1/2/3
*1
(9P, Female)
RS232C
RS422
*2
*1 The RS-232C-3 port can be used only when the BKP-7930
is installed.
*2 The RS-232C-2 and RS-232C-3 ports can be used for RS-
422 interfaceing by changing the switch setting of S802 to
S806 on the IF-777 board.
8-4-1-3
REMOTE (8P, Female)
*3
CCU1 to CCU6 CONNECTOR
6PIN . . POWER (+) IN
7PIN . . POWER (–) IN
RCP1 to RCP6, AUX1, AUX2, MSU
6PIN . . POWER (+) OUT (RCP POWER +25 V)
7PIN . . POWER (-–) OUT (GND for Power)
VCS CONNECTOR
6PIN . . NOT USED
7PIN . . NOT USED
No.
Signal
Specifications
1
DCD IN
DATA CARRIER DETECT
2
RXD IN
RECEIVED DATA
3
TXD OUT
TRANSMITTED DATA
4
DTR OUT
DATA TERMINAL READY
5
SIGNAL GND
SIGNAL GND
6
DSR IN
DATA SET READY
7
RTS OUT
REQUEST TO SEND
8
CTS IN
CLEAR TO SEND
9
NC
—
No.
Signal
Specifications
1
DCD IN
DATA CARRIER DETECT
2
RXD IN
RECEIVED DATA
3
TXD (+) OUT
TRANSMITTED DATA
4
TXD (-) OUT
TRANSMITTED DATA
5
SIGNAL GND
SIGNAL GND
6
RXD (-) IN
RECEIVED DATA
7
RTS OUT
REQUEST TO SEND
8
CTS IN
CLEAR TO SEND
5
9
6
1
(External view)
9
NC
—
No.
Signal
Specifications
1
TX (+)
CNU SERIAL DATA
2
TX (–)
3
RX (+)
MSU/RCP/CCU/VCS/AUX
SERIAL DATA
4
RX (–)
5
TX GND
GND for TX
6
POWER (+)
*3
7
POWER (–)
*3
8
SPARE
CHASSIS GND
CHASSIS GND
No.
Signal
Specifications
1
2
3
4
5
6
7
8
(External view)
RCP/CCU/MSU/VCS
AUX 1/2/3/4
Summary of Contents for HDC-900 Series
