4-15 (E)
BKP-5090
4-1-6. System Config Menu
The System config menu is used for adjustments items necessary to replace a printed circuit board or
some parts of the camera. The System config menu is not normally accessible. To display this menu,
switch setting of the AT-126 board is required.
To activate the System config menu, first display the TOP menu.
(Boxed items under “Settings” indicate the factory setting. XX or XXX represents two or three digits in hexadecimal.)
Page
Ver.
Item
Settings
Contents
Date/Time
YY/MM/DD
Adjusts the built-in calender and timer.
HH:MM:SS
Reset
Turn MENU SELECT
Resets hour (HH), minute (MM) and second (SS) of the timer.
knob to execute.
Y/Chroma
SC FREQ.
XXX (
[XX]
)
Adjusts the camera’s subcarrier frequency.
Y SYNC
XXX (
[XX]
)
Adjusts the sync level of camera’s Y output signal.
Y Setup
XXX (
[XX]
)
Adjusts the setup level of camera’s Y output signal.
Y Video
XXX (
[XX]
)
Adjusts the Y level of camera’s Y output signal.
Test Setup
XXX (
[XX]
)
Adjusts the setup level of camera’s encoder output signal.
Burst LVL
XXX (
[XX]
)
Adjusts the burst level of camera’s encoder output signal.
Chroma LVL
XXX (
[XX]
)
Adjusts the chroma level of camera’s encoder output signal.
Q/V LVL
XXX (
[XX]
)
Adjusts the Q(V) level of camera’s encoder output signal.
SC-H Phase
XXX (
[XX]
)
Adjusts the SC-H phase of camera’s encoder output signal.
REG LVL
XXX (
[XX]
)
Sets the level of the R, G and B output signals
(Video and SYNC levels vary together)
VF
XXX (
[XX]
)
Sets the level of the R, G and B output signals
(Only the video level varies)
REG LVL
XXX (
[XX]
)
Adjusts the level of the R, G and B output signals.
CB
On,
[Off]
Turns on and off the camera color-bar signal to be output in setting
each item on the Y/Chroma page.
PR/VA/Test
VA MOD R/G/B XXX (
[XX]
)
Adjusts the R, G or B modulation balance for the VA board.
G Clock
XXX (
[XX]
)
Adjusts the clock pulse in phase to be input to the AD converter for G
signal on the PR board.
(Note : In replacing OHB, readjustment is required to set the maximum
value of the modulation depth.
R/B Clock
XXX (
[XX]
)
Adjusts the clock pulse in phase to be input to the AD converter for R/B
signals on the PR board.
(Note: In replacing OHB, readjustment is required to set the minimum
level of a pseudo signal.)
M.Black
XXX (
[XX]
)
Adjusts the master black signal.
Test 2 HI
XXX (
[XX]
)
Adjusts the high level of the Test 2 (3-STEP) signal on the VA board.
Test 2 MID
XXX (
[XX]
)
Adjusts the middle level of the Test 2 (3-STEP) signal on the VA board.
Test CLIP
XXX (
[XX]
)
Adjusts the clip level of the Test 1 (sawtooth) signal on the VA board.
Test
1, 2,
[Off]
Selects a test signal to be output in setting each item on the PR/VR/
Test page.
1
: Outputs the sawtooth test signal
2
: Outputs the 3-step waveform test signal
Off
: No test signal is output
4-1. Setup Menu (BVP-500 series)
4-1-6. System Config Menu
