3-8 (E)
BKP-5090
Page
Ver.
Item
Settings
Contents
Detail 2
Detail
[On]
, Off
Turns the function on and off to improve resolution by adding detail signal.
H/V Ratio
–99 to 99 (
[0]
)
Adjusts the mix ratio of H and V detail signal.
Frequency
–99 to 99 (
[0]
)
Adjusts the boost frequency for H detail signal.
MIX Ratio
–99 to 99 (
[0]
)
Adjusts the mix ratio of H detail signal used before and after the gamma
compensation circuit.
W.Limitter
–99 to 99 (
[0]
)
Adjust the clipping level adainst the higher detail signal at the maximum level.
B.Limitter
–99 to 99 (
[0]
)
Adjusts the clippping level against the lower detail signal at the minimum level.
Comb
–99 to 99 (
[0]
)
Sets the effect volume of the comb filter
99 (Causes less cross colors.)
↔
–99 (Yields clear pictures, but causes
more cross colors.)
*
For a PAL model, this function has the effect on not every object but a
specified object.
Knee APT.
On,
[Off]
Turns the knee aperture function on and off
Knee APT.
_
99 to 99 (
[0]
)
Adjusts the detail level for signals which exceeds the knee point to
emphasize the detail of the highlight
Test
1, 2,
[Off]
Selects the test signal.
1
: Outputs the sawtooth waveform test signal
2
: Outputs 3-step waveform test signal
Off
: No test signal is output
Clear
Press MENU SEL
Sets all settings on the Detail 2 page to 0.
switch to execute.
(When you press MENU SEL switch, the “Clear” indication flashes.
Press MENU SEL switch again to execute; press CANCEL button to
cancel.)
Skin Detail
Master SW
On,
[Off]
Turns the skin tone detail function on and off
n
When set to On, the setting of SkinDTL for No. 1 shown below
is always On
SkinDTL
1 : On
Turns the skin tone detail function on and off for each selection 1 to 3 of
2 : On,
[Off]
Gate.
3 : On,
[Off]
Level
1 :
_
99 to 99 (
[0]
)
Adjusts the skin tone detail for each selection 1 to 3 of Gate item.
2 :
_
99 to 99 (
[0]
)
3 :
_
99 to 99 (
[0]
)
Phase
1 : 0 to 359 (
[120]
)
Sets the color phase that is the center of the color area where the skin
2 : 0 to 359 (
[120]
)
tone detail function is to be activated for each selection 1 to 3 of Gate
3 : 0 to 359 (
[120]
)
item.
Width
1 : 0 to 90 (
[0]
)
Sets the width of the color area around the phase where the skin tone
2 : 0 to 90 (
[0]
)
detail function is to be activated for each selection 1 to 3 of Gate item.
3 : 0 to 90 (
[0]
)
Sat
1 :
_
99 to 99 (
[0]
)
Sets the saturation for which the skin tone detail function is to be
2 :
_
99 to 99 (
[0]
)
activated for each selection 1 to 3 of Gate item.
3 :
_
99 to 99 (
[0]
)
Gate
[1]
, 2, 3, irs
1, 2, 3 : Selects the gate marker showing the area where the skin
tone detail function is activated
irs :
Indicates the auto-iris detection area when the unit is put into
the “Skn” mode by using the Operation menu, Auto Iris/Knee
page
Gate Vf
On,
[Off]
Turns on and off the gate marker indication selected by the above
Gate item
Auto Hue
Press MENU SEL
Sets the skin tone detail hue function automatically
switch to execute.
Clear
Press MENU SEL
Sets all settings on the Skin Detail page to 0.
switch to execute.
(When you press MENU SEL switch, the “Clear” indication flashes.
Press MENU SEL switch again to execute; press CANCEL button to cancel.)
3-1. Setup Menu (BVP-550 series)
3-1-2. Paint Menu