Home
/
SONIX
/
SN32F260 Series
/
User Manual

SONIX SN32F260 Series, User Manual

Share

Page: 59 / 141

SONIX SN32F260 Series User Manual Download Page 59

SN32F260 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 59

Version 1.5

6

6

6

16-BIT TIMER0 WITH CAPTURE

FUNCTION

6.1 OVERVIEW

Each Counter/timer is designed to count cycles of the peripheral clock (PCLK) or an externally supplied clock and can
optionally generate interrupts or perform other actions at specified timer values based on four match registers. Each
counter/timer also includes one capture input to trap the timer value when an input signal transitions, optionally
generating an interrupt.

In PWM mode, up to 23 match and 1 global registers can be used to provide a single-edge controlled PWM output on
the match output pins.

6.2 FEATURES



Two 16-bit counter/timers with a programmable 8-bit prescaler.



Counter or timer operation



Two 16-bit capture channels that can take a snapshot of the timer value when an input signal transitions. A
capture event may also optionally generate an interrupt.



The timer and prescaler may be configured to be cleared on a designated capture event. This feature permits
easy pulse-width measurement by clearing the timer on the leading edge of an input pulse and capturing the timer
value on the trailing edge.



Four 16-bit match registers that allow:

–

Continuous operation with optional interrupt generation on match.

–

Stop timer on match with optional interrupt generation.

–

Reset timer on match with optional interrupt generation.



Up to 22(CT16B1) PWM outputs corresponding to match registers with the following capabilities:

–

Set LOW on match.

–

Set HIGH on match.

–

Toggle on match.

–

Do nothing on match.

6.3 PIN DESCRIPTION

Pin Name

Type

Description

GPIO Configuration

CT16Bn_CAP0

I

Capture channel input 0.

Depends on GPIOn_CFG

CT16Bn_PWMx

O

Output channel x of Match/PWM output.

«
...
57
58
59
60
61
...
»

Summary of Contents for SN32F260 Series














































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands