SONIX SN32F260 Series Page 63 User Manual Download | Manualshive

Page: 63 / 141

background image

SN32F260 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 63

Version 1.5

6.6.2 PWM Mode 2



PWMn is 1 when TC<MRn during Up-counting period.

Take Edge-aligned up-counting Mode as example,

1.

All single edge controlled PWM outputs go HIGH at the beginning of each PWM cycle (timer is set to zero) unless
their match value in CT16Bn_MR0~3 registers is equal to zero.

2.

Each PWM output will go LOW when its match value is reached. If no match occurs, the PWM output remains
continuously HIGH.

3.

If a match value larger than the PWM cycle length is written to the CT16Bn_MR0~3 registers, and the PWM
signal is LOW already, then the PWM signal will go HIGH on the next start of the next PWM cycle.

4.

If a match register contains the same value as the timer reset value (the PWM cycle length), then the PWM output
will be reset to HIGH on the next clock tick. Therefore, the PWM output will always consist of a one clock tick wide
low pulse with a period determined by the PWM cycle length.

5.

If a match register is set to zero, then the PWM output will go LOW the first time the timer goes back to zero and
will stay LOW continuously.

CT16Bn_MR0=60

0

100 (TC resets)

60

25

CT16Bn_MR1=25

PWM0

PWM1

CT16Bn_MR2=100

PWM2

CT16Bn_TC



Note:

When the match outputs are selected to perform as PWM outputs, the timer reset (MRnRST) and

timer stop (MRnSTOP) bits in

CT16Bn_MCTRL

register must be set to zero except for the match

register setting the PWM cycle length. For this register, set the MRnR bit to one to enable the timer
reset when the timer value matches the value of the corresponding match register.

«
...
61
62
63
64
65
...
»

Summary of Contents for SN32F260 Series














































































































































Reviews:

No comments

Related manuals for SN32F260 Series

Brand: Microchip Technology Pages: 37

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Brand: Ultraflex Pages: 7

Brand: Riello Pages: 72

SCENE MASTER - V1.0

Brand: JBSYSTEMS Light Pages: 24

Brand: CALEFFI Pages: 14

Brand: PXM Pages: 15

Brand: Rauch Pages: 85

CC2530-CC2592EM

Brand: Texas Instruments Pages: 3

Brand: VALPES Pages: 28

Brand: Danfoss Pages: 18

Brand: blackloud Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands