Sonex Aircraft Aerovee 2.1 Assembly And Installation Manual Download Page 23

Page: 23 / 70

AeroVee 2.1

Rev Z. 01/14/2015

Sonex Aircraft

LLC

ROCKER SHAFT INSTALLATION

Parts Required:

__ Push Rods, ACV-P06-51
__ Pushrod Measuring Tool
__ Cylinder Head Nuts and Washers, from ACV-P01-86
__ Rocker Arm Nuts, from Valve Cover package
__ Rocker Shaft Assembly, ACV-P02-10

Assembly Instructions:

Note: Pre-assembled rocker assemblies often need to be disas-

sembled for proper installation.

__ 1. Assemble the rocker shafts with the gap in the rocker

blocks facing the cupped end of the rocker arms and the

thin shims evenly distributed.

Note: Steps 3 through 19 apply to one side of the engine at a

time and will be repeated for each side.

__ 3. Place a square spacer from the rocker arm package over

each of the rocker shaft mounting studs on a cylinder

head.

__ 2. Turn each adjuster fully counter-clockwise until the pad

lightly contacts the rocker arm, and then turn it back

clockwise 1.5 turns.

The rocker blocks are installed so their gaps are toward the

cupped end of the rocker arms.

GAP IN ROCKER BLOCKS

Two different swivel pads exist. The one on the right is a large,

swiveling pad, the one on the right is a ball with a flat spot.

The flat spot on the ball must contact the valve's stem.

__ 4. Place a rocker assembly over the mounting studs and

inspect for interference between the rocker arm as-

sembly and the head studs. If the rocker arm assembly

contacts the head studs, trim the ends of the head studs

to remove the interference.

The spacers placed under the rocker blocks influence

the alignment of the rocker arm swivel pads to the valve

tip. Proper alignment is achieved when the flat of the

swivel pad is partially off-center from the valve stem.

This is typically achieved with 1 or 2 shims under each

rocker block.

Incorrect - Too

few spacers. The

swivel pad is cen-

tered on the valve

stem.

Incorrect - Too

many spacers. The

flat of the swivel

pad is off the edge

of the valve stem.

Correct

- The flat

of the swivel pad is

off center from the

valve stem but sits

fully on the valve

stem. Typically 1 or

2 shims.

Summary of Contents for Aerovee 2.1





































































Search results

Summary of Contents for Aerovee 2.1

Reviews:

Related manuals for Aerovee 2.1

Brands by name

Popular brands

Sonex Aircraft Aerovee 2.1, Assembly And Installation Manual

Search results

Summary of Contents for Aerovee 2.1

Reviews:

Related manuals for Aerovee 2.1

Brands by name

Popular brands