Sonex Aircraft Aerovee 2.1 Assembly And Installation Manual Download Page 31

Page: 31 / 70

AeroVee 2.1

Rev Z. 01/14/2015

Sonex Aircraft

LLC

FLYWHEEL INSTALLATION

Tools Required:

__Socket Wrench
__36mm Socket
__Torque Wrench
__Permatex High Temp Red RTV Silicone Gasket

Parts Required:

__ Flywheel Assembly, ACV-F01-02

Hardware Required

__ ACV-Z01-13 Cap Screws
__ ACV-Z01-20 Bolts
__ACV-Z01-21 Bolt
__ACV-Z01-24 Nut
__ACV-Z01-27 Washers

Assembly Instructions:

__1. Using a high-temperature silicone sealant, lightly coat

the dowel pin area of the flywheel and place a small bead

(1/8" diameter) in the groove near the dowel pin area of

the flywheel.

Note: The engine assembly DVD may show an O-ring

being used instead. The O-ring has been discontinued.

__2. Install the flywheel on

the back of the engine.

important: The 8 dowel

pins will only align one

way.

Note: The flywheel may

require some effort to

get it started and seated

on the drive pins. This is

normal.

__3. Install wavy washer and

gland nut with Locktite

272. Torque to 227 ft-lbs.

Note: A piece of wood

temporarily bolted to

the prop hub provides

good leverage to keep the

crank from turning while

the gland nut is being

torqued.

Summary of Contents for Aerovee 2.1





































































Search results

Summary of Contents for Aerovee 2.1

Reviews:

Related manuals for Aerovee 2.1

Brands by name

Popular brands

Sonex Aircraft Aerovee 2.1, Assembly And Installation Manual

Search results

Summary of Contents for Aerovee 2.1

Reviews:

Related manuals for Aerovee 2.1

Brands by name

Popular brands