background image

SOLUXTEC USER GUIDE 2021_Version 1/a_ALL RIGHTS RESERVED 

INTRODUCTION 

 

Thank you for electing SOLUXTEC GmbH PV modules. The following user guide covers 

important instructions to be read and understood before installation of SOLUXTEC products. 

This document does not have any relation to quality warranties and only acts as a user guide 

for electrical, mechanical and general handling safety of SOLUXTEC products. 

 

In  case PV  installation is not respecting below  mentioned points, the quality warranty of 

SOLXTEC products will become invalid. 

This document belongs to SOLUXTEC and all content is SOLUXTEC intellectual property. 

SOLUXTEC reserves the right to modify this document without prior notice. 

 

-  Please read this document carefully before installation 

 

-  Please make sure that this document is always available for installers and operators to 

handle SOLUXTEC products. 

 

-  Please give a copy of this document to the installation owner. 

 

-  If any questions are not well answered in this document, please contact SOLUXTEC 

support prior installation. 

 

 

SAFETY 

 

 

The installation of photovoltaic modules must respect the current standards from the 

place of installation. It is imperative to refer to the standards of each local authority 

in case specifics rules are imposed. 

 

 

Installation of photovoltaic modules must be operated  by qualified people  with 

sufficient knowledge of all regulations and compliance requirements specific to the 

country of installation. 

 

 

Solar modules create DC electricity and are even energized under a slight 

illumination level. Several modules connected together may occur an accumulation 

of voltage and intensity. Please respect all personal security to avoid a risk of 

electrocution. 

 

 

Please respect the data given from the elected module’s data sheet to respect all 

module’s limits and comply with other materials that will be need to operate the 

photovoltaic generator.  

 

 

 

-  Never open the junction box on the back of the photovoltaic module 

-  Make sure that connectors are clean and not dirty or wet before connection. 

-  Never disconnect the photovoltaic connector under load. Always turn off the DC breaker 

prior to any photovoltaics connector disconnection. 

-  Tools must be dedicated for solar installation and supporting DC current. 

-  The final photovoltaic generator must follow all needed standards and requirements in 

compliance with the installation country (PV, inverter, cable, grounding and other 

accessories from the PV generator). 

-  Never disassemble any part of the module. 

Summary of Contents for DMMVI370


















Reviews: