Solplanet ASW LT-G3 Series User Manual Download Page 13

Page: 13 / 71

12 User Manual UM0016_ASW 25K-40K-LT-G3_EN_V02_0622

3 Unpacking

3.1 Scope of delivery

Obje

Description

Quantity

Inverter

1 piece

Wall mounting bracket

1 piece

DC connector

2 pieces

Screw accessory

1 piece

AC connector

1 piece

4G/ WiFi Stick (optional)

1 piece

（

optional

）

RS485 communication terminal

1 piece

（

optional

）

Documentation

1 piece

Please carefully check all the components in the carton. If

anything is missing, contact your dealer at once.

3.2 Check for transport damage

Thoroughly inspect the packaging upon delivery. If you detect

any damage to the packaging which indicates the inverter may

have been damaged, inform the responsible shipping company

immediately. We will be glad to assist you if required.

Summary of Contents for ASW LT-G3 Series








































































Search results

Summary of Contents for ASW LT-G3 Series

Reviews:

Related manuals for ASW LT-G3 Series

Brands by name

Popular brands

Solplanet ASW LT-G3 Series, User Manual

Search results

Summary of Contents for ASW LT-G3 Series

Reviews:

Related manuals for ASW LT-G3 Series

Brands by name

Popular brands