Solidator 2.0 User Manual Download | Manualshive

Page: 15 / 20

background image

15

Solidator Shutdown Procedure

From the Solidator touch panel, press the power button, the following screen has three options.

Always perform a system shutdown before turning off the main power to the machine.

«
...
13
14
15
16
17
...
»

Summary of Contents for 2.0





















Reviews:

No comments

Related manuals for 2.0

Brand: Oki Pages: 40

Brand: Samsung Pages: 9

Bixolon SRP-500

Brand: Samsung Pages: 27

550N - CLP Color Laser Printer

Brand: Samsung Pages: 288

2 COLOR THERMAL PRINTER SRP-275

Brand: Samsung Pages: 8

Brand: Samsung Pages: 6

Brand: Samsung Pages: 91

Brand: JCM Pages: 22

Brand: Canon Pages: 198

Brand: Star Micronics Pages: 24

Daisy Wheel 410

Brand: Radio Shack Pages: 140

Brand: Radio Shack Pages: 42

Brand: Oce Pages: 230

Brand: Microcom Pages: 73

8860MFPD - Multifunction Inkjet Printer

Brand: Xerox Pages: 16

Brand: ZKTeco Pages: 38

iP6310D - PIXMA Color Inkjet Printer

Brand: Canon Pages: 2

iP5200R - PIXMA Color Inkjet Printer

Brand: Canon Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands