manualshive.com logo in svg

Solidator 2.0, User Manual

Share
Download
Solidator 2.0 User Manual Download Page 17

17 

 

Description of WLAN Setup and HTML 5 Interface 

-

 

Over to the Solidator. The file is saved into memory on the Solidator and the print job can be selected in the 
future. 

-

 

If you choose to use Network, a HTML5 Web Interface is available to load job files. 

-

 

You will be able to access the Solidator by entering the IP address of the Solidator in your  web browser, e.g., 
http://192.168.0.100 

-

 

To determine the IP address of the Solidator via LAN, connect an Ethernet cable to the Solidator and enter 
the IP address for your modem/router.  Search for devices using the network map. 

-

 

Enter the IP address that you have identified into your web browser to access the Web interface. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

-

 

To setup the Wi-Fi or Lan settings using the Solidator control panel. Click the Setup Icon in the Main 
Menu, then select Wi-Fi or LAN and enter the specifics of your networks as usual. 

Summary of Contents for 2.0





















Reviews:

No comments

Brands by name

Popular brands

Load more brands