Solid RocketWAVE SRF-L-1835 Product Manual Download Page 5

Page: 5 / 24

SOLiD RocketWAVE™ SRF-L-1835 Product Manual

V1.6 - DEC 2021

Page 5

Regulatory Compliance / Certifications for repeater

CE Radio Equipment Directive (RED) Directive

(2014/53/EU)

RF:

ETSI EN 301 908-15 V15.1.1

ETSI EN 301 908-1 V13.1.1 (2019-11)

ETSI TS 138 104 V16.8.0

EN50385:2017

EMC:

ETSI EN 301-489-1 V2.2.3

ETSI EN 301 489-50 V2.3.1

Safety:

EN IEC 62368-1 :2020+A11 :2020

RoHS

2011/65/EU Amended to 2015/863/EU

REACH

EC 1907/2006 REACH Regulation

Regulatory Compliance / Certifications for power supply

CE: EN60950-1 / 62368-1

Electrostatic Discharge Immunity:

IEC61000-4-2:2008

Radiation Electromagnetic Immunity

IEC61000=4-3:2006+A1:2007+A2:2010

FAST TRANSIENT IMMUNITY

IEC61000-4-4:2004

SURGE IMMUNITY

IEC61000-4-5:2005

CONDUCTED DISTURBANCES IMMUNITY

IEC61000-4-6:2008

VOLTAGE DIPS, INTERRUPTION & VARIATIONS

IEC61000-4-11:2004



The installation to comply with European EN50385 exposure compliance requirements, the following

Power Density limits/guidelines (mW/cm

) according to ICNIRP are valid:

0.2 for frequencies from 10 MHz to 400 MHz

F (MHz) / 2000 for frequencies from 400 MHz to 2 GHz

1 for frequencies from 2 GHz to 300 GHz



The power supply of the unit complies with Overvoltage Category II. It also complies with the surge re-

quirement according to EN 61000-4-5 (fine protection); however, installation of an additional medium

Summary of Contents for RocketWAVE SRF-L-1835























Search results

Summary of Contents for RocketWAVE SRF-L-1835

Reviews:

Related manuals for RocketWAVE SRF-L-1835

Brands by name

Popular brands

Solid RocketWAVE SRF-L-1835, Product Manual

Search results

Summary of Contents for RocketWAVE SRF-L-1835

Reviews:

Related manuals for RocketWAVE SRF-L-1835

Brands by name

Popular brands