Solid State Logic C200 routing guide Installation Manual Download

Page: 31 / 80

Section 5 – Installation Wiring

This section provides the details for connecting the system components together.

Power Supply Connections

This section refers to the following supplied cables :

Description

SSL Part No.

qty

Notes

Con IEC Free Socket 6A 2m

32VGL362

Centuri

Cable Power Digital 2m

32VALXVX

Main & Redundant Console power

Lead Chassis Earth 16m

66C93115

Console to Centuri

a) Connect the mains input lead to a suitable supply outlet.

THE MAINS SAFETY EARTH MUST BE CONNECTED

For systems where PSU redundancy is specified

– Connect both the console’s Harting mains leads to

independent mains supplies. For live transmissions work it is recommended that one of the power sources will be

from an un-interruptable source. The console is fitted with auto-ranging power supplies which will accept mains

voltages which range from 90 to 255V without adjustment.

THE TWO POWER SOURCES MUST NOT BE FROM DIFFERENT PHASES OF A 3-PHASE SUPPLY.

b) Connect the Centuri’s IEC lead(s) to appropriate mains supply outlet(s). If a redundant PSU module is specified refer

to the notes above for suitable supply provision.

The Centuri crate is also fitted with auto-ranging power supplies which will accept mains voltages which range from

100 to 240V without adjustment.

c) If specified, do not connect a source of power to the NetBridge until the voltage select switch position has been

confirmed. The NetBridge operates at either 115V or 230V ranges and its power supply must be set to the

appropriate range for the local supply.

Refer to the diagram on page 22 for the location of the voltage select switch.

Earth Wiring –

A chassis to chassis earth cable needs to be installed between the console and the processor.

This keeps the two earths at the same potential thus preventing currents flowing along the signal cables.

Run the green chassis earth cable from the Console’s chassis bolt to the similar earth bolt located on the Centuri

backpanel.

Installation Wiring

Section 5

Page 27

Summary of Contents for C200 routing guide

















































































Search results

Summary of Contents for C200 routing guide

Reviews:

Related manuals for C200 routing guide

Brands by name

Popular brands

Solid State Logic C200 routing guide, Installation Manual

Search results

Summary of Contents for C200 routing guide

Reviews:

Related manuals for C200 routing guide

Brands by name

Popular brands