background image

Electrical connection 

18 

Installation manual 

pellet

top

 

7.6  Other connections 

External boiler request (X28) 

Potential-free relay output for switching an external boiler, for example, an external boiler 
receives a release from the SOLARFOCUS boiler control; 

 

connect to X28 on SOLARFOCUS power element. 

Attention! 

The connection is potential-free and has a maximum load of 5A. 

 

 

Fault (X29) 

Potential-free relay output, for example, to switch a warning device (optical/acoustic) upon 
occurrence of an operating fault on the boiler; 

 

connect to X29 on the power element. 

Attention! 

The connection is potential-free and has a maximum load of 5A. 

 

 

External request (X51) 

Input, i.e. the SOLARFOCUS boiler can be started by an external control; 

 

connect to X51 on the power element. 

Attention! 

This connection must be potential-free. 

 

Connect the heating circuit pump (X9, X10) 

 

Connect heating circuit pump 1 to power element connector 

X9

 and heating circuit pump 2 

to 

X10

 

If required (e.g. in the case of underfloor heating), connect a limiting thermostat. 

 

If a limiting thermostat is not used, the contact must be bridged. 

 

7.7  Internet connection 

To connect the boiler control with the Internet, connect the Ethernet port 

X2

 (type RJ45) on the back of the dis-

play with a network router via cable. The connection is required in order to use the following functions: 
-  mySOLARFOCUS app 
-  Weatherman function 
-  IP-VNC (Remote access to the boiler control) 
-  Sending e-mails 

7.8  Types of sensors - overview 

Measuring 

sleeve 

Cable 

Sensor type 

Art.No. 

Use 

Colour 

Material / finish 

Length 

15 cm 

silver 

Stainless steel braid 

3 m  PT100 

69688 

Flue gas temperature sensor (pellet

plus

, octo

plus

thermi

nator

 I) 

1.6 m  PT100 

69681 

Flue gas temperature sensor (thermi

nator

 II 22-30) 

2.1 m  PT100 

69682 

Flue gas temperature sensor (thermi

nator

 II 36-60, 

pellet

top

, pellet

plus 

1 m  PT100 

69680 

Feed sensor rotary valve (pellet

top

 , octo

plus

 ) 

13 cm 

grey 

PVC cable 

2 m  PT1000 

1622 

Flow sensor for fresh water module 

fast

 

5 cm 

red 

Silicone cable 

2.1 m  PT100 

69687 

Feed sensor pellets / wood chips feed 

red 

Silicone cable 

3 m  KTY81-110 

69686 

Return sensor, boiler temperature sensor, external 
boiler sensor 

black 

PVC cable 

3 m  KTY81-110 

69095 

Tank sensor 

 

PVC cable 

5 m  PT1000 

69095-1000  Tank sensor 

black 

PVC cable 

5 m  PT1000 

69098-1000  Flow sensor 

 

Silicone cable 

5 m  KTY81-110 

69689 

Return sensor pellet

top

 70 

2 cm 

grey 

PVC twin cable 

2 m  PT1000 

1621-PT 

Tank sensor 

white 

PVC twin cable 

2 m  KTY81-210/B 

1621 

Tank sensor 

red 

Silicone cable 

2 m  KTY81-210/B 

1620 

Collector sensor 

black 

Silicone cable 

2 m  PT1000 

1620-PT 

Collector sensor 

2 cm x 1.5 Ø 
Contact sen-

sor 

black 

PVC cable 

2 m  KTY81-110 

69098 

Flow sensor 

to be provided on-site 

KTY81-110 

69096 

External sensor; (plastic housing 66x60x39 mm) 

to be provided on-site 

PT1000 

69096-1000  External sensor; (plastic housing 66x60x39 mm) 

 

Summary of Contents for pellet top touch 35

































Reviews: